Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonHarsh shifts and limp mode overheat the fluid quickly, and overheated fluid kills transmissions - keep driving short and gentle, because a delayed solenoid fix can turn into a rebuild.
One of the electric valves that controls your transmission's hydraulic pressure isn't doing what the computer tells it. Expect harsh or slipping shifts, or the transmission stuck in a single gear until it's fixed.
Key facts
P2818 means pressure Control Solenoid H Stuck On. One of the electric valves that controls your transmission's hydraulic pressure isn't doing what the computer tells it. Expect harsh or slipping shifts, or the transmission stuck in a single gear until it's fixed. WrenchFair's published fair-price range for this repair is $80–$450 parts and $250–$700 labor at independent shops.
WrenchFair rates P2818 a 4-of-5 DIY difficulty (“Diagnosis is DIY-friendly with a scan tool and multimeter, but the repair usually means dropping the transmission pan and sometimes the valve body.”) with a “Diagnose soon” driveability rating: Harsh shifts and limp mode overheat the fluid quickly, and overheated fluid kills transmissions - keep driving short and gentle, because a delayed solenoid fix can turn into a rebuild. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
transmission in limp mode (stuck in one gear)
slipping between shifts
hard or banging shifts
transmission overheating
worse fuel economy
Likely causes
pressure control solenoid H stuck open from debris or wear
contaminated transmission fluid
valve body fault holding the solenoid circuit energized
wiring short keeping the solenoid powered
faulty pcm driver (rare - rule out solenoid and wiring first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Research TSBs for your transmission. Tests: contaminated transmission fluid
2. Check fluid condition - debris can jam a solenoid plunger open. Tests: pressure control solenoid H stuck open from debris or wear
3. With a scan tool, watch solenoid H state: if it reads on even when commanded off, the solenoid is mechanically stuck or the circuit is shorted to power. Tests: pressure control solenoid H stuck open from debris or wear
4. Inspect the control wiring for a short to voltage before condemning the solenoid. Tests: wiring short keeping the solenoid powered
5. If the circuit is good, the pan comes off: inspect the solenoid, its filter screen, and the valve body for debris or sticking valves.
6. Replace the faulty solenoid (with fresh fluid and a new filter while the pan is off), clear the code, and verify pressure control on a test drive.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$80 – $450
Labor$250 – $700
Replacing the faulty pressure control solenoid H, usually with fresh fluid and a new filter while the pan is off. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2818 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Diagnosis is DIY-friendly with a scan tool and multimeter, but the repair usually means dropping the transmission pan and sometimes the valve body.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →