Diagnose soonHarsh shifts and limp mode overheat the fluid quickly, and overheated fluid kills transmissions - keep driving short and gentle, because a delayed solenoid fix can turn into a rebuild.
One of the electric valves that controls your transmission's hydraulic pressure isn't doing what the computer tells it. Expect slipping, harsh shifts, overheating, or the transmission stuck in a protective limp mode until it's fixed.
Key facts
P2813 means pressure Control Solenoid G Control Circuit Range/Performance. One of the electric valves that controls your transmission's hydraulic pressure isn't doing what the computer tells it. Expect slipping, harsh shifts, overheating, or the transmission stuck in a protective limp mode until it's fixed. WrenchFair's published fair-price range for this repair is $80–$450 parts and $250–$700 labor at independent shops.
WrenchFair rates P2813 a 4-of-5 DIY difficulty (“Diagnosis is DIY-friendly with a scan tool and multimeter, but the repair usually means dropping the transmission pan and sometimes the valve body.”) with a “Diagnose soon” driveability rating: Harsh shifts and limp mode overheat the fluid quickly, and overheated fluid kills transmissions - keep driving short and gentle, because a delayed solenoid fix can turn into a rebuild. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2014–2016 Nissan Rogue (2.5L QR25DE) — CVT judder / shudder — P17F0 diagnosis ladder:Owner-verified
Diagnosis starts with a scan and a fluid check; the valve body lives inside the CVT behind the pan. Whether the fix is a valve body or a full unit hinges on the belt inspection.
Do this test first: 1. Research TSBs for your transmission.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P2813 on the 2014–2016 Nissan Rogue — but the community-sourced CVT judder / shudder — P17F0 diagnosis ladder note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
CVT pan / valve body fasteners: verify — Valve body bolt torque not confirmed from a source; confirm against factory service info before torquing.
Tips
Signature: shudder or judder on acceleration, especially uphill, sometimes with the CVT dropping into a limp mode that caps RPM. Codes: P17F0, P17F1, plus P0776, P2813, P1715, P0841.
Nissan's own TSB ladder: inspect the belt and pulleys for slip damage first. Belt OK → replace the valve body plus a TCM calibration write. Belt damaged → full CVT assembly. Don't authorize a full CVT before the belt inspection — the valve body is the cheaper, common fix.
Fluid matters more than owners expect: degraded NS-3 fluid loses shear stability and the steel belt slips on the pulleys. One 2nd-gen owner's jerky, shuddering launches were cured by a CVT drain-and-fill — start with fresh genuine Nissan NS-3 before condemning hardware.
Ask the dealer about TSB/goodwill coverage by VIN before authorizing out-of-pocket work — Nissan has a published decision tree for exactly these codes, and 2014–2016 Rogues were the subject of a class action over this shudder.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light on
transmission in limp mode (stuck in one gear)
slipping between shifts
hard or banging shifts
transmission overheating
worse fuel economy
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
solenoid G coil degrading (resistance drifting out of spec)
corroded connector adding resistance to the circuit
partially damaged wiring
degraded fluid making the solenoid respond sluggishly
faulty valve body affecting actual pressure response
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Research TSBs for your transmission.
2. Check fluid condition - sluggish hydraulic response can set a range/performance code even with good wiring. Tests: faulty valve body affecting actual pressure response
3. Inspect the connector for corrosion that adds resistance to the circuit. Tests: corroded connector adding resistance to the circuit
4. Compare the circuit's behavior against the service procedure; a coil drifting out of spec or a sticky valve means replacement. Tests: solenoid G coil degrading (resistance drifting out of spec)
5. If the circuit is good, the pan comes off: inspect the solenoid, its filter screen, and the valve body for debris or sticking valves.
6. Replace the faulty solenoid (with fresh fluid and a new filter while the pan is off), clear the code, and verify pressure control on a test drive.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2014–2016 Nissan Rogue: CVT judder / shudder — P17F0 diagnosis ladder — test first, then buy for this job.
The price range below is a national planning range for P2813 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$80 – $450
Labor$250 – $700
Replacing the faulty pressure control solenoid G, usually with fresh fluid and a new filter while the pan is off. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2813 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Diagnosis is DIY-friendly with a scan tool and multimeter, but the repair usually means dropping the transmission pan and sometimes the valve body.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →