Diagnose soonA transmission that cannot shift or is stuck in limp mode is a breakdown risk. Address as soon as possible.
The input/turbine speed sensor B signal is completely missing - the transmission may refuse to shift.
Key facts
P2767 means input Turbine Shaft Speed Sensor B Circuit No Signal. The input/turbine speed sensor B signal is completely missing - the transmission may refuse to shift. WrenchFair's published fair-price range for this repair is $40–$250 parts and $100–$500 labor at independent shops.
WrenchFair rates P2767 a 3-of-5 DIY difficulty (“Fluid check, wiring inspection, and sensor cleaning are DIY; testing the sensor and circuits needs a service manual and multimeter.”) with a “Diagnose soon” driveability rating: A transmission that cannot shift or is stuck in limp mode is a breakdown risk. Address as soon as possible. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2006–2014 Dodge Charger (3.5L V6, 5.7L HEMI V8, 6.1L HEMI V8) — NAG1 limp mode — conductor plate / speed sensors:Owner-verified
Pan drop from below — the conductor plate lives on top of the valve body inside the NAG1 (W5A580) 5-speed. Valve body comes out; no transmission removal needed. Fill through the dipstick tube (Chrysler/Dodge dipstick tool).
Do this test first: Check for Technical Service Bulletins for the particular vehicle - this may be a known issue with a known fix.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P2767 on the 2006–2014 Dodge Charger — but the community-sourced NAG1 limp mode — conductor plate / speed sensors note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Valve body / pan bolts: verify — Torque specs for valve body and pan bolts not confirmed from a forum source — confirm against factory service info before torquing.
Tips
Learn the signature: the car locks into 2nd gear (limp mode) and won't shift; a restart temporarily clears it. A generic scanner shows P0700 (TCM asking for the light), but you need a scanner that talks to the TCM to see the real codes: P0717 or P2767 (input speed sensor signal loss).
The input/output speed sensors live ON the conductor plate inside the transmission — the proven fix is conductor-plate replacement (valve body out, pan off), documented step-by-step for Charger/Magnum/Challenger/300 in the linked DIY video.
Check the cheap cause first: the 13-pin transmission connector. ATF wicks up through a leaking pilot bushing into the harness connector and causes identical limp-mode symptoms — inspect it for oil before buying a conductor plate.
Don't chase engine codes for a transmission limp mode: a basic OBD reader can't see TCM codes, which is why owners replace throttle bodies and sensors first and the limp mode keeps coming back.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
intermittent or erratic speedometer (odometer) operation
inability of the transmission to shift at all
inoperative speedometer and/or odometer
erratic or harsh transmission shift points
a decrease in fuel efficiency
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
A faulty input speed sensor B
Damaged, loose, or shorted wiring and/or connectors in the circuit
Excessive metal debris on the sensor magnetic contacts
Damaged reluctor wheel
PCM failure or a PCM programming error
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 9 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for Technical Service Bulletins for the particular vehicle - this may be a known issue with a known fix.
Perform a visual inspection of system wiring and connectors; repair or replace shorted or open circuits before proceeding. Tests: Damaged, loose, or shorted wiring and/or connectors in the circuit
Test the battery and inspect battery cables and cable ends; test alternator output.
Retrieve all stored codes and note freeze frame data.
If both input and output sensor codes are present, use the scanner data stream to determine which circuit is malfunctioning.
Check for excessive metal debris on the sensor magnetic contacts; clean before reinstallation; inspect the reluctor wheel notches for damage or wear.
Test individual sensor resistance and circuit voltage with the DVOM per manufacturer specifications; replace sensors that fail.
Disconnect related controllers before testing resistance or continuity - failure to do so may damage the controller.
If all circuits and sensors are good, suspect a faulty PCM or PCM programming error.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2006–2014 Dodge Charger: NAG1 limp mode — conductor plate / speed sensors — test first, then buy for this job.
The price range below is a national planning range for P2767 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $250
Labor$100 – $500
Input/turbine speed sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2767 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Fluid check, wiring inspection, and sensor cleaning are DIY; testing the sensor and circuits needs a service manual and multimeter.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →