Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonLimp-in mode with harsh shifts can damage the transmission. Address as soon as possible.
The transmission input/turbine speed sensor B circuit is malfunctioning - expect harsh shifts or limp-in mode.
Key facts
P2765 means input Turbine Shaft Speed Sensor B Circuit. The transmission input/turbine speed sensor B circuit is malfunctioning - expect harsh shifts or limp-in mode. WrenchFair's published fair-price range for this repair is $40–$250 parts and $100–$500 labor at independent shops.
WrenchFair rates P2765 a 3-of-5 DIY difficulty (“Fluid check, wiring inspection, and sensor cleaning are DIY; testing the sensor and circuits needs a service manual and multimeter.”) with a “Diagnose soon” driveability rating: Limp-in mode with harsh shifts can damage the transmission. Address as soon as possible. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
harsh or erratic transmission shift points
failure of the transmission to shift
decreased fuel efficiency
speedometer (odometer) fluctuation
lack of speedometer (odometer) operation
in some cases, when coming to a stop the engine may stall
Likely causes
Defective input speed sensor B
Faulty output speed sensor B
Damaged, worn, or broken reluctor ring or shaft
Bad transmission torque converter
Loose, burned, or otherwise damaged wiring and/or connectors
PCM failure or programming error
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 10 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for Technical Service Bulletins for the particular vehicle - this may be a known issue with a known fix.
Perform a visual inspection of system wiring and connectors; repair or replace disconnected, corroded, burnt, or shorted parts. Tests: Loose, burned, or otherwise damaged wiring and/or connectors
Test the battery and inspect battery cables and cable ends; remove corrosion and secure terminals.
Retrieve all stored codes and note freeze frame data.
If both input sensor and output sensor codes are present, use the scanner data stream to determine which circuit is malfunctioning.
When removing sensors, check for excessive metal debris on magnetic contacts and remove it; inspect the reluctor wheel notches.
Test individual sensors with the DVOM per manufacturer specifications; replace sensors that fail.
Disconnect related controllers before testing resistance and continuity; repair or replace defective circuits.
If all circuits and sensors are good, suspect a faulty PCM or PCM programming error.
Note: sensor-to-reluctor clearance is critical on some applications - make sure mounting surfaces and threaded holes are clear of obstruction.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $250
Labor$100 – $500
Input/turbine speed sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2765 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Fluid check, wiring inspection, and sensor cleaning are DIY; testing the sensor and circuits needs a service manual and multimeter.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →