P2610: Ecm/pcm Internal Engine Off Timer Performance
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonAddress with some urgency - ignition cycle monitoring affects fuel, timing, and shifting, and ignoring it can damage the catalytic converter. Wiring faults are common; do not assume the PCM is bad.
The engine computer is losing track of when the engine is off - it may affect fuel delivery, timing, and shifting.
Key facts
P2610 means ecm/pcm Internal Engine Off Timer Performance. The engine computer is losing track of when the engine is off - it may affect fuel delivery, timing, and shifting. WrenchFair's published fair-price range for this repair is $60–$400 parts and $100–$300 labor at independent shops.
WrenchFair rates P2610 a 4-of-5 DIY difficulty (“Scan tool checks and CPS wiring inspection are DIY-capable; PCM programming or replacement is shop-level.”) with a “Diagnose soon” driveability rating: Address with some urgency - ignition cycle monitoring affects fuel, timing, and shifting, and ignoring it can damage the catalytic converter. Wiring faults are common; do not assume the PCM is bad. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
initially no obvious symptoms
diminished engine performance
decreased fuel efficiency
engine drivability symptoms over time
Likely causes
ECM/PCM programming errors
Defective ECM/PCM
Open or shorted wiring or connectors
Faulty crankshaft position sensor (CPS) or shorted CPS wiring
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 8 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for Technical Service Bulletins for the specific vehicle - it may be a known issue with a known fix.
If any crankshaft position sensor codes are present, diagnose and repair those before diagnosing P2610. Tests: Faulty crankshaft position sensor (CPS) or shorted CPS wiring
Retrieve all stored codes and freeze frame data; clear codes and test drive to see if P2610 resets.
With a scan tool, observe CPS and engine RPM data with the key on and engine off (KOEO) - RPM readings other than 0 indicate a defective CPS or shorted CPS wiring. Tests: Open or shorted wiring or connectors
Use a digital volt/ohmmeter to check ignition coil primary voltage with the ignition off - above 5 V indicates a wiring short to voltage.
Using vehicle-specific information, determine the exact parameters the ECM/PCM uses to detect engine shut-off; disconnect related controllers before testing circuit resistance to prevent ECM/PCM damage.
Repair or replace defective circuits and retest; clear codes and drive normally until the ECM/PCM enters readiness mode.
If all circuits are within specs, suspect a defective PCM or PCM programming error.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $400
Labor$100 – $300
Crankshaft position sensor replacement or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2610 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Scan tool checks and CPS wiring inspection are DIY-capable; PCM programming or replacement is shop-level.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →