P2564: Turbo Boost Control Position Sensor Circuit Low
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonPoor performance and hesitation can make merging and passing unsafe. Diagnose soon; the PCM is unlikely the cause.
The turbo boost sensor signal is stuck too low - expect poor performance and hesitation.
Key facts
P2564 means turbo Boost Control Position Sensor Circuit Low. The turbo boost sensor signal is stuck too low - expect poor performance and hesitation. WrenchFair's published fair-price range for this repair is $40–$200 parts and $80–$250 labor at independent shops.
WrenchFair rates P2564 a 3-of-5 DIY difficulty (“Visual inspection and connector cleaning are DIY; multimeter circuit tests need basic electrical skills; PCM is shop-level.”) with a “Diagnose soon” driveability rating: Poor performance and hesitation can make merging and passing unsafe. Diagnose soon; the PCM is unlikely the cause. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
malfunction indicator light on
poor performance
hesitation during acceleration
decrease in fuel economy
Likely causes
Short to ground in the signal circuit to the TBCPS sensor
Short to ground in the power circuit at the TBCPS sensor
Failed TBCPS sensor
Corroded or damaged connector/terminals
Failed PCM (unlikely)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 8 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for Technical Service Bulletins for the specific vehicle - it may be a known issue with a known fix.
Locate the TBCPS sensor (usually screwed or bolted into the turbocharger housing). Tests: Short to ground in the signal circuit to the TBCPS sensor
Visually inspect the connector and wiring for scraping, rubbing, bare wires, burn spots, or melted plastic. Tests: Corroded or damaged connector/terminals
Pull the connector apart and inspect the terminals for burning or green corrosion; clean with electrical contact cleaner and a plastic bristle brush, dry, and apply electrical grease. Tests: Corroded or damaged connector/terminals
Clear the code with a scan tool; if it does not return, the connection was the problem.
If it returns, test the TBCPS power and ground circuits KOEO per manufacturer specs (12 V or 5 V); repair opens in wiring.
Test the signal wire for a short to ground; repair if found.
If all tests pass, the TBCPS sensor has likely failed - replace it. PCM failure is unlikely.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $200
Labor$80 – $250
Turbo boost control position sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2564 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Visual inspection and connector cleaning are DIY; multimeter circuit tests need basic electrical skills; PCM is shop-level.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →