Drive safeEmissions-only system active at cold start. Safe to drive.
A valve in the cold-start air system is stuck open, which can let hot exhaust flow backward and destroy the air pump. Fix it before the pump dies too.
Model notes: A stuck-open switching valve is a pump killer - exhaust backflow destroys the pump quickly. If the valve failed open, budget for a pump inspection at minimum.
Key facts
P2440 means secondary air injection system switching valve stuck open, bank 1. A valve in the cold-start air system is stuck open, which can let hot exhaust flow backward and destroy the air pump. Fix it before the pump dies too. WrenchFair's published fair-price range for this repair is $100–$300 parts and $150–$350 labor at independent shops.
WrenchFair rates P2440 a 3-of-5 DIY difficulty (“Replace the check valve with the switching valve - backflow damage is the real risk.”) with a “Drive safe” driveability rating: Emissions-only system active at cold start. Safe to drive. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 776 factory bulletins on file for this vehicle (mostly Equipment, Structure, Electrical System) — see the latest ones
On your 2009–2015 Toyota Tacoma (4.0L 1GR-FE V6, 2.7L 2TR-FE I4) — Secondary air injection failure (P2440/P0418):Owner-verified
The air switching valve sits on the side of the engine head near the exhaust manifold (12mm nuts, one tucked behind the valve); the pump and relay live in the engine-bay fuse/relay area. No intake removal needed for the relay test.
Do this test first: Remove the valve and check for exhaust soot inside the air passages - soot means backflow has occurred
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P2440 on the 2009–2015 Toyota Tacoma — but the community-sourced Secondary air injection failure (P2440/P0418) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Air switching valve nuts: verify — 12mm nuts per owner writeup; torque spec not confirmed from a forum source — confirm against factory service info before torquing.
Tips
Check the relay first — a documented owner fix traced P2440 to a failed #55 relay: swap it with the horn relay (#40) and see if the horn misbehaves with the suspect relay in its place. Minutes, nearly free, and it has cleared the code.
A valve stuck open puts the truck in limp mode; moisture, pump debris, and carbon are the usual causes. Also check the small hose between the valve and the pressure sensor — a deteriorated hose sets the same family of codes.
Out of warranty, the owner consensus is the Hewitt-Tech bypass kit (~$145, about an hour to install, splices into the MAF harness) versus roughly $2,500 for the dealer's whole-system replacement — multiple owners report 10k+ miles trouble-free. Honest note: it's an emissions-system bypass, so check your state's inspection rules before going that route.
Warning repeated across threads: do not buy cheap aftermarket SAIS valves — owners report them failing in weeks to months, some warrantied two or three times before giving up. Toyota replaces the system as a unit because one failing part sends debris through the rest.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Typical time: “Out of warranty, the owner consensus is the Hewitt-Tech bypass kit (~$145, about an hour to install, splices into the MAF harness) versus roughly $2,500 for the dealer's whole-system replacement — multiple owners report…” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
failed emissions test
eventual air pump failure from exhaust backflow
possible exhaust leak noise
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Carbon-fouled switching valve stuck open (most common)
Failed valve solenoid
Failed check valve allowing exhaust backflow
Vacuum supply problem (vacuum-operated designs)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Remove the valve and check for exhaust soot inside the air passages - soot means backflow has occurred Tests: Failed check valve allowing exhaust backflow
Test the valve's ability to close fully
Replace the check valve at the same time - it is the backflow protection Tests: Failed check valve allowing exhaust backflow
Inspect the air pump for exhaust contamination; a soot-filled pump needs replacement too Tests: Failed check valve allowing exhaust backflow
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2009–2015 Toyota Tacoma: Secondary air injection failure (P2440/P0418) — test first, then buy for this job.
The price range below is a national planning range for P2440 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$100 – $300
Labor$150 – $350
Pump or valve replacement is typical. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2440 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Replace the check valve with the switching valve - backflow damage is the real risk.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →