Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonCould result in catastrophic engine damage; severe. Do not drive until diagnosed.
Fuel injection pressure is too high - on diesels this can indicate a serious engine timing or lubrication problem.
Model notes: Seen almost exclusively on high-pressure diesel injection applications. Applies to Ford, Range Rover, BMW, Peugeot, Hyundai.
Key facts
P2288 means injector Control Pressure Too High. Fuel injection pressure is too high - on diesels this can indicate a serious engine timing or lubrication problem. WrenchFair's published fair-price range for this repair is $50–$500 parts and $150–$800 labor at independent shops.
WrenchFair rates P2288 a 5-of-5 DIY difficulty (“Diesel high-pressure injection diagnosis requires gauges, factory data, and experience; engine timing may be involved.”) with a “Diagnose soon” driveability rating: Could result in catastrophic engine damage; severe. Do not drive until diagnosed. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
no start condition
excessive smoke from the exhaust
peculiar noises from engine compartment
Likely causes
Defective high-pressure injection pressure switch
Open or shorted control circuits
Low oil level
Low oil pressure
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 8 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Research technical service bulletins for the specific vehicle first.
Make sure the engine is filled to the appropriate oil level and no oil pressure or oil level lamps are illuminated; if they are, perform a manual oil pressure test. Tests: Defective high-pressure injection pressure switch
Retrieve all stored codes and freeze frame data, record them, then clear codes and test-drive until the code restores or the PCM enters readiness mode.
Visually inspect related wiring and connectors; repair or replace wiring that has been cut, burned, or damaged.
Use the DVOM to test voltage and ground circuits at the injection system pressure sensor; check system fuses if no voltage.
If voltage is present, test the corresponding circuit at the PCM connector; an open circuit between the sensor and PCM is suspect if absent there.
Test the injection pressure sensor with the DVOM against manufacturer specifications; replace if non-compliant.
Note: although listed for some gasoline applications, this code is seen almost exclusively in high-pressure diesel injection applications with an engine timing issue.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $500
Labor$150 – $800
High-pressure injection pressure sensor replacement; engine timing repairs cost more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2288 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
5 of 5 — Diesel high-pressure injection diagnosis requires gauges, factory data, and experience; engine timing may be involved.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →