P2286: Injector Control Pressure Sensor Circuit High
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonCan be severe - internal engine damage is possible if not corrected; engine may not start. Diagnose promptly.
The fuel injection pressure sensor signal is too high - on diesel trucks (especially the 6.0L Powerstroke) this points to the ICP sensor or its circuit.
Model notes: Seen on 2005 Ford F-250 6.0L Powerstroke (with P2285). Applies to Toyota, Ford, Dodge, Chrysler, Jeep, Chevrolet, GMC.
Key facts
P2286 means injector Control Pressure Sensor Circuit High. The fuel injection pressure sensor signal is too high - on diesel trucks (especially the 6.0L Powerstroke) this points to the ICP sensor or its circuit. WrenchFair's published fair-price range for this repair is $50–$300 parts and $100–$400 labor at independent shops.
WrenchFair rates P2286 a 4-of-5 DIY difficulty (“Advanced diesel fuel/oil pressure diagnosis; the ICP sensor on a 6.0L Powerstroke is hard to reach (behind and below the turbo, driver side).”) with a “Diagnose soon” driveability rating: Can be severe - internal engine damage is possible if not corrected; engine may not start. Diagnose promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
engine may not start
low fuel pressure
low oil pressure
check engine light illuminated
Likely causes
Defective injector control pressure sensor
Low oil or fuel level
Oil pump malfunction
Defective fuel pump
Faulty or damaged wiring
Loose or defective control module ground strap
Corroded, damaged or loose connector
Defective fuse or fusible link
Defective PCM
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Research technical service bulletins for the specific vehicle first.
Check oil and fuel levels to ensure they are adequate. Tests: Low oil or fuel level
Locate all injector control pressure sensor circuit components and inspect wiring for scraping, rubbing, bare wires, or burn spots; check connectors for security, corrosion, and damaged pins. Tests: Defective injector control pressure sensor
Verify the reference voltage (normally approximately five volts from the PCM) and ground; continuity testing with power removed.
For advanced diagnosis, use fuel and oil pressure gauges to verify actual pressures against specifications.
Common mistake: replacing the ICP sensor or fuel pump when defective wiring is the actual cause.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $300
Labor$100 – $400
Injector control pressure sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2286 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Advanced diesel fuel/oil pressure diagnosis; the ICP sensor on a 6.0L Powerstroke is hard to reach (behind and below the turbo, driver side).
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →