P2282: Air Leak Between Throttle Body and Intake Valves
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSeverely diminished performance and engine may shut off on acceleration; rectify as quickly as possible.
There is an air leak between the throttle body and the intake valves - usually a large vacuum leak at the intake manifold or its gasket.
Model notes: Seen on 2005 Saturn Vue 6-cylinder and 2017 Ford Fiesta ST. Applies to Vauxhall, Chevrolet, Suzuki, Saturn, Ford.
Key facts
P2282 means air Leak Between Throttle Body and Intake Valves. There is an air leak between the throttle body and the intake valves - usually a large vacuum leak at the intake manifold or its gasket. WrenchFair's published fair-price range for this repair is $30–$200 parts and $100–$400 labor at independent shops.
WrenchFair rates P2282 a 3-of-5 DIY difficulty (“A leak this size is usually audible; intake manifold gasket replacement is intermediate to advanced depending on the vehicle.”) with a “Diagnose soon” driveability rating: Severely diminished performance and engine may shut off on acceleration; rectify as quickly as possible. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
severely diminished engine performance
engine may shut off upon acceleration
backfires upon acceleration
accompanying misfire codes
Likely causes
Large vacuum leak on or near the intake manifold
Bad intake manifold gasket
Defective throttle body gasket
Defective MAP or MAF sensor
PCM or programming error
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Research technical service bulletins for the specific vehicle first.
With the engine running, carefully check the intake manifold area for signs of a vacuum leak - a leak large enough to set this code will likely be very evident; do not forget the EGR valve and PCV valve. Tests: Large vacuum leak on or near the intake manifold
If MAF codes accompany the P2282, inspect the MAF sensor hot wire for debris and clean only per manufacturer recommendations.
Retrieve all stored codes and freeze frame data, record them, then clear codes and test-drive until readiness or the code resets.
If the code resets, test the MAF and MAP sensors per manufacturer specifications using the DVOM, then test system circuits with the voltage drop method.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $200
Labor$100 – $400
Intake manifold or throttle body gasket replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2282 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — A leak this size is usually audible; intake manifold gasket replacement is intermediate to advanced depending on the vehicle.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →