P2274: O2 sensor signal biased/stuck lean bank 1 sensor 3
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonUsually no drivability impact since this is a downstream monitor sensor, but emissions and catalyst monitoring are compromised. Diagnose reasonably soon.
The second downstream O2 sensor (after the second catalytic converter) on bank 1 is stuck reading lean - it thinks there is too much oxygen in the exhaust.
Model notes: Auto brands include Mazda, Ford, VW, Mercedes-Benz. Sensor 3 refers to a third sensor downstream of a second catalytic converter.
Key facts
P2274 means o2 sensor signal biased/stuck lean bank 1 sensor 3. The second downstream O2 sensor (after the second catalytic converter) on bank 1 is stuck reading lean - it thinks there is too much oxygen in the exhaust. WrenchFair's published fair-price range for this repair is $50–$200 parts and $50–$150 labor at independent shops.
WrenchFair rates P2274 a 3-of-5 DIY difficulty (“Visual inspection and downstream O2 sensor replacement are intermediate work; live-data monitoring requires a scan tool.”) with a “Diagnose soon” driveability rating: Usually no drivability impact since this is a downstream monitor sensor, but emissions and catalyst monitoring are compromised. Diagnose reasonably soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
most likely no drivability issues since this is not sensor 1
malfunction indicator lamp (MIL) illumination
in some cases the engine may run rough
Likely causes
Exhaust leak near O2 sensor
Contaminated or failed HO2S (sensor 3)
HO2S wiring/circuit problem
Loose installation of HO2S
Fuel pressure incorrect
Faulty fuel injector
Engine coolant leak
Faulty purge solenoid valve
PCM failure
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Visually inspect the wiring and connectors for corrosion, rubbed/chafed/bent wires, bent/loose pins, burnt appearance, or crossed wires.
Check for exhaust leaks near the O2 sensor and repair as necessary. Tests: Exhaust leak near O2 sensor
Using a DVOM set to ohms, check harness connectors for resistance and compare to manufacturer specifications.
With the engine at normal operating temperature in closed loop, monitor bank 1 sensor 3 readings on the scan tool - a stuck-lean rear HO2S will likely sit at 0V; revving the engine should cause the voltage to change. Tests: Contaminated or failed HO2S (sensor 3)
If replacing the O2 sensor, buy an OEM one for best results; inspect a removed sensor for fuel, engine oil, and coolant contamination.
If the sensor checks out, test fuel pressure, inspect the purge solenoid valve, fuel injectors, and coolant passages for leaks.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $200
Labor$50 – $150
Oxygen sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2274 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Visual inspection and downstream O2 sensor replacement are intermediate work; live-data monitoring requires a scan tool.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →