Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSevere: cylinder imbalance often stems from mechanical engine failure. Rectify as quickly as possible.
Cylinder four is burning a different air-fuel mix than the other cylinders, and the computer is flagging it.
Model notes: Applies to Toyota, Audi, Kia, VW, Lexus, and many other OBD-II vehicles.
Key facts
P219F means cylinder 4 Imbalance Error. Cylinder four is burning a different air-fuel mix than the other cylinders, and the computer is flagging it. WrenchFair's published fair-price range for this repair is $50–$300 parts and $100–$400 labor at independent shops.
WrenchFair rates P219F a 4-of-5 DIY difficulty (“Per-cylinder imbalance often traces to mechanical engine issues; scope testing CKP/CMP signals is professional-level work.”) with a “Diagnose soon” driveability rating: Severe: cylinder imbalance often stems from mechanical engine failure. Rectify as quickly as possible. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
diminished fuel efficiency
lack of general engine performance
stored misfire codes or lean/rich exhaust codes
check engine light
Likely causes
Inadequate engine compression
Defective oxygen sensor/s
Faulty CKP or CMP sensor
Burnt, chafed, broken, or disconnected wiring or connectors
Faulty mass air flow or manifold air pressure sensor
Bad fuel pump or clogged fuel filter
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Address any stored misfire, throttle position, MAP, or MAF codes before diagnosing P219F; the engine must run smoothly and any rich or lean condition must be repaired first.
Search for TSBs matching the code, vehicle, and symptoms - a known fix can shortcut the diagnosis.
Record all stored codes and freeze-frame data, then clear codes and test drive until the code returns or the PCM enters readiness mode.
Visually inspect related wiring and connectors; repair any wiring that is cut, burned, or damaged. Tests: Burnt, chafed, broken, or disconnected wiring or connectors
With the engine at operating temperature and idling, observe oxygen sensor data on the scanner data stream; sensors that fail to cycle adequately with a healthy engine should be considered defective.
Use an oscilloscope to test for voltage spikes or glitches in the CKP and CMP sensor inputs.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $300
Labor$100 – $400
Sensor replacement or mechanical engine repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P219F ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Per-cylinder imbalance often traces to mechanical engine issues; scope testing CKP/CMP signals is professional-level work.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →