P2184: Engine coolant temperature sensor 2 circuit low input
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonCan cause poor drivability and improper fan operation - diagnose within a reasonable time frame. If the engine is actually overheating, shut it down immediately.
The second coolant temperature sensor is reporting a voltage too low - the computer thinks the engine is extremely hot.
Model notes: Seen on Honda, Toyota, Volkswagen, Mazda, Dodge, Ford, and other vehicles with two coolant temperature sensors.
Key facts
P2184 means engine coolant temperature sensor 2 circuit low input. The second coolant temperature sensor is reporting a voltage too low - the computer thinks the engine is extremely hot. WrenchFair's published fair-price range for this repair is $20–$100 parts and $80–$200 labor at independent shops.
WrenchFair rates P2184 a 3-of-5 DIY difficulty (“Inspecting and replacing the ECT sensor is DIY-friendly; short-to-ground circuit diagnosis is intermediate.”) with a “Diagnose soon” driveability rating: Can cause poor drivability and improper fan operation - diagnose within a reasonable time frame. If the engine is actually overheating, shut it down immediately. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
poor fuel economy
poor drivability
engine may run rough or blow black smoke
may not idle
may start and then die
Likely causes
Bad ECT sensor #2
Short to ground on ECT #2 signal circuit
Faulty or damaged connectors
Damaged wiring harness
Loose terminals at ECT or PCM
Possibly an overheated engine
Bad PCM
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your vehicle.
If the engine was overheated, diagnose that first. Tests: Possibly an overheated engine
Using a scan tool with key on/engine off, check the #2 ECT reading on a cold engine - it should match the IAT sensor reading. If it does not, replace the sensor.
If the reading shows excessively hot (more than 260 deg F), unplug the sensor - the reading should drop to extreme cold (around -30 deg F). If it does, the sensor is internally shorted.
If the reading does not change when unplugged, check for a short to ground on the signal circuit - look for chafing or melted wiring.
Use a wiggle test on the harness while watching the ECT reading on the scan tool.
Suspect the PCM only after the sensor and wiring check out.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$20 – $100
Labor$80 – $200
ECT sensor #2 replacement, wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2184 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Inspecting and replacing the ECT sensor is DIY-friendly; short-to-ground circuit diagnosis is intermediate.
Torque specs: Thermostat housing bolts: typically 8–12 Nm. Aluminum threads strip easily — verify spec and use a torque wrench.
Pro tip: Bleed the cooling system per the factory procedure after refilling, or trapped air will overheat the engine and fake a “still broken” reading.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →