Diagnose soonABS may be disabled and transmission shifting irregular; diagnose promptly.
The voltage signal from vehicle speed sensor B is too low - the computer is not getting a clean speed reading from that sensor.
Key facts
P2160 means vehicle speed sensor B low input. The voltage signal from vehicle speed sensor B is too low - the computer is not getting a clean speed reading from that sensor. WrenchFair's published fair-price range for this repair is $30–$200 parts and $80–$250 labor at independent shops.
WrenchFair rates P2160 a 3-of-5 DIY difficulty (“Visual inspection, cleaning debris from sensors, and replacing a speed sensor are DIY-friendly; oscilloscope waveform diagnosis is advanced.”) with a “Diagnose soon” driveability rating: ABS may be disabled and transmission shifting irregular; diagnose promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2008–2013 Chevrolet Tahoe Hybrid (6.0L V8) — No-start diagnosis (no conventional starter):Owner-verified
Diagnostic only: use a hybrid-aware scan tool and a helper to watch the crankshaft pulley. Do not touch high-voltage hardware for this test.
Do this test first: Visually inspect system wiring, speed sensors, and connectors - repair open or shorted circuits.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P2160 on the 2008–2013 Chevrolet Tahoe Hybrid — but the community-sourced No-start diagnosis (no conventional starter) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Diagnostic fasteners (covers, disconnect): verify — No torque values involved in this diagnostic note.
Tips
Remember there is no conventional 12V starter to fail: the two motor-generators inside the 2ML70 crank the engine through the crankshaft at about 1500 rpm. If you hear nothing from under the hood during a no-start, think hybrid system, not starter motor.
Do the eyeball test: have someone attempt a start while you watch the crankshaft pulley. If the crank is actually spinning and it will not fire, the fault is ignition or fuel, not hybrid. If the crank is not moving, suspect the transmission input/output shaft side.
Pull the matching codes: P16F3, P2160, P077B, and P0722 point at the transmission-side start and speed signals on these trucks.
After any hybrid service work, reseat the orange high-voltage service disconnect on the pack until it gives its full two-step click — a half-seated disconnect is a common no-start cause — and confirm the underhood inverter cover is back on, since a missing cover triggers the interlock and blocks start.
Clearing codes with a generic scanner is not enough after a hybrid shutdown; the dealer needs to run a full computer reset (about an hour) or the shutdown can recur.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Typical time: “Clearing codes with a generic scanner is not enough after a hybrid shutdown; the dealer needs to run a full computer reset (about an hour) or the shutdown can recur.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
erratic speedometer/odometer operation
irregular transmission shift patterns
service engine soon lamp illuminated
traction control lamp illuminated
antilock brake lamp illuminated
unexpected activation/deactivation of traction control
other transmission and abs codes stored
abs system may be rendered inoperable
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Excessive metal debris buildup on the speed sensor
Defective wheel speed or vehicle speed sensor
Cut or damaged wiring harness or connectors, especially near speed sensors
Damaged or worn teeth on a reluctor ring
Faulty PCM, ABCM, or EBCM (less likely)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 8 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Visually inspect system wiring, speed sensors, and connectors - repair open or shorted circuits. Tests: Cut or damaged wiring harness or connectors, especially near speed sensors
Clean excessive metallic debris from the affected sensors and check reluctor ring integrity. Tests: Excessive metal debris buildup on the speed sensor
Retrieve all stored codes and freeze-frame data with a scanner before clearing.
Check technical service bulletins for your vehicle. Tests: Defective wheel speed or vehicle speed sensor
Observe wheel speed and vehicle speed on the scanner data stream while test driving.
Perform a resistance test on the sensor in question with a DVOM against manufacturer specifications.
Use an oscilloscope to check the waveform for glitches or inconsistencies.
If the code appeared immediately after a brake or transmission repair, suspect a damaged sensor harness or connector.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2008–2013 Chevrolet Tahoe Hybrid: No-start diagnosis (no conventional starter) — test first, then buy for this job.
The price range below is a national planning range for P2160 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $200
Labor$80 – $250
Vehicle speed sensor replacement, wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2160 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Visual inspection, cleaning debris from sensors, and replacing a speed sensor are DIY-friendly; oscilloscope waveform diagnosis is advanced.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →