P2084: Exhaust gas temperature (EGT) sensor circuit range/performance bank 1 sensor 2
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYou can usually drive, but the computer can no longer protect the converter from overheating - get it fixed before a long hot run.
The exhaust temperature sensor after the converter on bank 1 (the side with cylinder 1) is reading out of range - usually a failed sensor, a corroded or loose connector, or wiring shorted to ground.
Key facts
P2084 means exhaust gas temperature (EGT) sensor circuit range/performance bank 1 sensor 2. The exhaust temperature sensor after the converter on bank 1 (the side with cylinder 1) is reading out of range - usually a failed sensor, a corroded or loose connector, or wiring shorted to ground. WrenchFair's published fair-price range for this repair is $40–$250 parts and $100–$300 labor at independent shops.
WrenchFair rates P2084 a 4-of-5 DIY difficulty (“Locating and replacing the sensor is straightforward; testing the sensor's resistance and heating it to watch the response needs the factory specs.”) with a “Diagnose soon” driveability rating: You can usually drive, but the computer can no longer protect the converter from overheating - get it fixed before a long hot run. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
no other readily recognizable symptoms
Likely causes
Loose or corroded connectors or terminals (most common)
Broken wires or missing insulation shorting to ground
Failed EGT sensor
Aftermarket exhaust without EGT provisions
Faulty PCM (unlikely)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model.
Locate the bank 1 sensor 2 EGT sensor - in the exhaust pipe downstream of the catalytic converter. Tests: Aftermarket exhaust without EGT provisions
Check the connectors and pigtail for corrosion, loose terminals, and missing insulation or bare wires shorting to ground. Tests: Broken wires or missing insulation shorting to ground
Remove the EGT sensor and check its resistance with an ohmmeter against the factory spec.
Heat the sensor with a hair dryer or heat gun while watching the ohmmeter - resistance should drop as it heats and rise as it cools.
With the key on, measure the reference voltage at the engine side of the pigtail against the factory spec.
Replace the sensor if it fails the resistance or response test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $250
Labor$100 – $300
EGT sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2084 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Locating and replacing the sensor is straightforward; testing the sensor's resistance and heating it to watch the response needs the factory specs.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →