P2066

P2066 on a 2005–2013 Chevrolet Corvette: Fuel level sensor B circuit range/performance

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P2066 on a 2005–2013 Chevrolet Corvette

DIY difficulty 3/5

The secondary fuel gauge sender (B circuit) is reading out of range - often a failed sender, a stuck float arm, or corroded connections at the tank. The gauge may read empty or full all the time.

Key facts

☑ Before you buy parts — check these first:
On your 2005–2013 Chevrolet Corvette (6.0L V8 (LS2), 6.2L V8 (LS3), 7.0L V8 (LS7), 6.2L supercharged V8 (LS9)) — Erratic/dead fuel gauge (sulfur on sender, P2066): Owner-verified
The additive fix is trivially DIY. Sender replacement is a shop/lift job (tank drop) unless you're set up for it.
Do this test first: Check for technical service bulletins for your make and model.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P2066 on the 2005–2013 Chevrolet Corvette — but the community-sourced Erratic/dead fuel gauge (sulfur on sender, P2066) note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Tips

Sources: MotorTrend - How to Fix Your C6 Corvette Fuel Gauge (TSB 05-00-89-078C, Techron procedure) · CorvetteForum - DTC P2066 Fuel Level Sensor B (right-tank sender fouling)

Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 8 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check for technical service bulletins for your make and model.
  2. Locate the fuel level sensor on your vehicle (usually in the fuel tank or on the fuel pump module). Tests: Failed fuel level sensor / sensing arm stuck mechanically (most common)
  3. Visually inspect the connector and wiring at the tank for scraping, rubbing, bare wires, corrosion, or melted plastic. Tests: Corroded connector or wiring at the fuel tank (very common)
  4. Clean the terminals with electrical contact cleaner, let dry, and apply dielectric grease.
  5. Clear the codes and see if P2066 returns - if not, the connections were the problem.
  6. If it returns, test the sensor signal voltage and ground against the factory specs with a multimeter.
  7. If the sensor resistance is out of spec, replace the fuel level sensor.
  8. Only suspect the PCM after the sensor and wiring are proven good.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2005–2013 Chevrolet Corvette: Erratic/dead fuel gauge (sulfur on sender, P2066) — test first, then buy for this job.
The price range below is a national planning range for P2066 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$50 – $400
Labor$200 – $600

Fuel level sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2066 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Connector inspection and cleaning at the tank are easy; replacing the sender means dropping the tank or removing the pump module, which is a bigger job.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: Sensor mounting bolts: typically 8–12 Nm — verify spec. Never overtighten sensors with plastic bodies.

Pro tip: Check wiring and connectors first — chafed wires and corroded pins cause more sensor codes than dead sensors do.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →