P205E: Reductant tank temperature sensor circuit intermittent
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe SCR system can be disabled, which raises emissions and can damage the catalyst if ignored - get it diagnosed promptly.
The DEF tank temperature sensor keeps cutting in and out - usually a loose connector, a broken lock tab, or chafed wiring. The system cannot manage DEF heating properly, so the SCR system can shut down.
Key facts
P205E means reductant tank temperature sensor circuit intermittent. The DEF tank temperature sensor keeps cutting in and out - usually a loose connector, a broken lock tab, or chafed wiring. The system cannot manage DEF heating properly, so the SCR system can shut down. WrenchFair's published fair-price range for this repair is $100–$500 parts and $150–$450 labor at independent shops.
WrenchFair rates P205E a 4-of-5 DIY difficulty (“Connector inspection and a wiggle test with live data are DIY-able; circuit testing needs the factory flowcharts.”) with a “Diagnose soon” driveability rating: The SCR system can be disabled, which raises emissions and can damage the catalyst if ignored - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on, may come and go
reduction in fuel efficiency
excessive black smoke from the exhaust
diminished engine performance
other SCR-related codes
Likely causes
Loose connector pin or broken lock tab in the sensor circuit (most common)
Chafed wiring that only breaks contact intermittently
Corroded connector pins
Defective reductant tank temperature sensor
Bad SCR controller/PCM or programming error (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model.
Inspect the tank temperature sensor connector for damage, corrosion, and a disconnected plug. Tests: Defective reductant tank temperature sensor
Retrieve all codes and freeze-frame data, record it, clear the codes, and drive to see if P205E resets.
With a scan tool watching the sensor reading, wiggle the harness and connector to try to reproduce the dropout. Tests: Loose connector pin or broken lock tab in the sensor circuit (most common)
Test the temperature sensor against the factory specs and replace it if it is out of range.
If the sensor tests good, test the input and output signal circuits between the sensor and the PCM/SCR controller with the controllers disconnected.
Only suspect the controller or PCM after the sensor and wiring are all proven good.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$100 – $500
Labor$150 – $450
Reductant tank temperature sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P205E ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Connector inspection and a wiggle test with live data are DIY-able; circuit testing needs the factory flowcharts.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →