P2056: Reductant injection valve circuit open bank 2 unit 2
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe SCR system can be disabled, which raises emissions and can damage the catalyst if ignored - get it diagnosed promptly.
The second DEF injector on bank 2 (the side without cylinder 1) has no power reaching it - usually a broken wire, a blown fuse, or a failed injector. DEF dosing is wrong, so emissions climb and the SCR system can shut down.
Key facts
P2056 means reductant injection valve circuit open bank 2 unit 2. The second DEF injector on bank 2 (the side without cylinder 1) has no power reaching it - usually a broken wire, a blown fuse, or a failed injector. DEF dosing is wrong, so emissions climb and the SCR system can shut down. WrenchFair's published fair-price range for this repair is $150–$700 parts and $150–$450 labor at independent shops.
WrenchFair rates P2056 a 4-of-5 DIY difficulty (“Visual inspection of the harness and connectors is easy; testing the injector control circuit needs the factory flowcharts and a scan tool that can activate the injector.”) with a “Diagnose soon” driveability rating: The SCR system can be disabled, which raises emissions and can damage the catalyst if ignored - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
diminished engine performance
excessive black smoke from the exhaust
reduction in fuel efficiency
other SCR-related codes
Likely causes
Open or shorted circuits in the reductant injection valve control wiring (most common)
Bad reductant injection valve (solenoid failed open)
Blown fuse in the SCR control system power supply
Insufficient DEF in the reservoir
Bad SCR controller/PCM or programming error (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model.
Visually inspect the reductant heater and injector harnesses and connectors for burnt or damaged wiring and repair it before proceeding. Tests: Open or shorted circuits in the reductant injection valve control wiring (most common)
Retrieve all codes and freeze-frame data, record it, clear the codes, and drive to see if P2056 resets.
Test fuses with the circuit loaded to avoid misdiagnosis, and verify battery voltage and ground at the SCR control system. Tests: Blown fuse in the SCR control system power supply
Use the scan tool to activate the bank 2 unit 2 reductant injector valve and test the output control circuit voltage.
If the control voltage is good, test the injection valve itself against the factory specs and replace it if it fails.
Only suspect the controller or PCM after the valve, wiring, and power supply are all proven good.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$150 – $700
Labor$150 – $450
Reductant injection valve replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2056 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Visual inspection of the harness and connectors is easy; testing the injector control circuit needs the factory flowcharts and a scan tool that can activate the injector.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →