P2046: Reductant temperature sensor circuit intermittent
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe SCR system can be disabled, which raises emissions and can damage the catalyst if ignored - get it diagnosed promptly.
The sensor that measures your diesel exhaust fluid (DEF) temperature keeps cutting in and out - usually a loose connector, a broken lock tab, or a chafed wire. The SCR system can shut down, which raises emissions and can eventually hurt the catalyst.
Key facts
P2046 means reductant temperature sensor circuit intermittent. The sensor that measures your diesel exhaust fluid (DEF) temperature keeps cutting in and out - usually a loose connector, a broken lock tab, or a chafed wire. The SCR system can shut down, which raises emissions and can eventually hurt the catalyst. WrenchFair's published fair-price range for this repair is $80–$400 parts and $100–$300 labor at independent shops.
WrenchFair rates P2046 a 3-of-5 DIY difficulty (“Checking the connector and doing a wiggle test with live data are easy; sensor and controller testing need the factory specs and pin-outs.”) with a “Diagnose soon” driveability rating: The SCR system can be disabled, which raises emissions and can damage the catalyst if ignored - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on, may come and go
reduction in fuel efficiency
excessive black smoke from the exhaust
diminished engine performance
other SCR-related codes
Likely causes
Loose connector pin or broken lock tab in the sensor circuit (most common)
Chafed wiring that only breaks contact intermittently
Corroded connector pins
Defective reductant temperature sensor
Bad SCR controller/PCM or programming error (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model.
Retrieve all codes and freeze-frame data, record it, clear the codes, and drive to see if P2046 resets.
Firmly check the sensor connector and every connection in its circuit - loose pins, broken lock tabs, and chafed wires are the top suspects. Tests: Loose connector pin or broken lock tab in the sensor circuit (most common)
With a scan tool watching the DEF temperature reading, wiggle the harness and connector to try to reproduce the dropout. Tests: Loose connector pin or broken lock tab in the sensor circuit (most common)
Inspect the harness for chafing, bare wires, or corrosion and repair as needed.
If the wiring proves good, test the sensor against the factory specs and replace it if it fails.
Only suspect the controller or PCM after the sensor and wiring are all proven good.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$80 – $400
Labor$100 – $300
Wiring repair or reductant temperature sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2046 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Checking the connector and doing a wiggle test with live data are easy; sensor and controller testing need the factory specs and pin-outs.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →