Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car drives normally and this will not strand you, but the converter/DPF is running without its heat protection - fix it before towing or hard driving.
The exhaust temperature sensor on bank 1 is reading too low a voltage - usually a wire shorted to ground, damaged insulation, or a dying sensor. The car drives normally, but the converter or DPF is running without its heat protection.
Key facts
P2032 means eGT sensor circuit low bank 1 sensor 2. The exhaust temperature sensor on bank 1 is reading too low a voltage - usually a wire shorted to ground, damaged insulation, or a dying sensor. The car drives normally, but the converter or DPF is running without its heat protection. WrenchFair's published fair-price range for this repair is $40–$250 parts and $80–$250 labor at independent shops.
WrenchFair rates P2032 a 2-of-5 DIY difficulty (“The sensor sits in the exhaust before the converter or DPF and is usually reachable from under the car; the tough part is that exhaust bolts are often rusted solid.”) with a “Diagnose soon” driveability rating: The car drives normally and this will not strand you, but the converter/DPF is running without its heat protection - fix it before towing or hard driving. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
no other symptoms will be readily noticeable
Likely causes
Loose or corroded connectors or terminals in the EGT sensor circuit (most common)
Broken wires or missing insulation shorting to ground
Failed EGT sensor
Aftermarket catback exhaust installed with no EGT provision
Failed computer (very rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Raise the vehicle and locate the EGT sensor on bank 1 - between the exhaust manifold and the converter, or before the DPF on a diesel. Tests: Aftermarket catback exhaust installed with no EGT provision
Check the connector and pigtail for corrosion, loose terminals, and bare wires shorting to ground. Tests: Loose or corroded connectors or terminals in the EGT sensor circuit (most common)
Disconnect the sensor and test its resistance with an ohmmeter against the factory spec, heating it gently to confirm the resistance changes with temperature.
With the key on, check for the reference voltage at the engine side of the pigtail per the factory spec.
Replace the sensor if it fails testing; repair any wiring issues found.
Only suspect the computer after the sensor and wiring are all proven good.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $250
Labor$80 – $250
EGT sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2032 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The sensor sits in the exhaust before the converter or DPF and is usually reachable from under the car; the tough part is that exhaust bolts are often rusted solid.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →