P2028: EVAP fuel vapor temperature sensor circuit intermittent
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonLow severity - the car is safe to drive - but fix it before your emissions test, since this code is an automatic failure.
The sensor watching fuel-vapor temperature keeps cutting in and out - usually a loose connector, a pin not seated, or a wire that only breaks contact sometimes. The car drives fine, but the light will come and go and it will fail an emissions test.
Key facts
P2028 means eVAP fuel vapor temperature sensor circuit intermittent. The sensor watching fuel-vapor temperature keeps cutting in and out - usually a loose connector, a pin not seated, or a wire that only breaks contact sometimes. The car drives fine, but the light will come and go and it will fail an emissions test. WrenchFair's published fair-price range for this repair is $30–$200 parts and $100–$300 labor at independent shops.
WrenchFair rates P2028 a 2-of-5 DIY difficulty (“Intermittent faults need a wiggle test while watching live data; the connector inspection itself is easy, but be gentle with brittle EVAP lines.”) with a “Diagnose soon” driveability rating: Low severity - the car is safe to drive - but fix it before your emissions test, since this code is an automatic failure. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on, may come and go
failed emissions test
slight decrease in fuel efficiency
fuel smell
abnormal fuel filling - slow fill-ups or the pump clicking off early
Likely causes
Loose connector pin, broken lock tab, or poorly seated fuse/connector in the sensor circuit (most common)
Corroded or melted connector pins
Chafed wiring that only breaks contact intermittently
Defective EVAP fuel vapor temperature sensor
Wire shorting to power or excessive resistance in the circuit
ECM issue (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Locate the fuel vapor temperature sensor and firmly check every connector in its circuit - loose pins, broken lock tabs, and poorly seated fuses are the top suspects. Tests: Loose connector pin, broken lock tab, or poorly seated fuse/connector in the sensor…
Inspect the harness for chafing and the connector pins for corrosion or melting; repair as needed. Tests: Corroded or melted connector pins
With a scan tool watching the sensor reading, wiggle the harness and connectors to try to reproduce the dropout. Tests: Loose connector pin, broken lock tab, or poorly seated fuse/connector in the sensor…
Clear the code and drive normally to see if it returns.
If it returns with the wiring proven good, test the sensor itself per the factory pin-out procedure.
Only suspect the ECM after the sensor, wiring, and connectors are all proven good.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $200
Labor$100 – $300
Connector repair or EVAP fuel vapor temperature sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2028 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Intermittent faults need a wiggle test while watching live data; the connector inspection itself is easy, but be gentle with brittle EVAP lines.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →