P2026: EVAP fuel vapor temperature sensor circuit low voltage
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonLow severity - the car is safe to drive - but fix it before your emissions test, since this code is an automatic failure.
The sensor watching fuel-vapor temperature is reading too low a voltage - usually a shorted wire, corroded connector, or a dying sensor. The car drives fine, but it will fail an emissions test.
Key facts
P2026 means eVAP fuel vapor temperature sensor circuit low voltage. The sensor watching fuel-vapor temperature is reading too low a voltage - usually a shorted wire, corroded connector, or a dying sensor. The car drives fine, but it will fail an emissions test. WrenchFair's published fair-price range for this repair is $30–$200 parts and $100–$300 labor at independent shops.
WrenchFair rates P2026 a 2-of-5 DIY difficulty (“Most of this is under-car inspection of wiring and plastic lines; be gentle with brittle EVAP lines, which crack easily when disturbed.”) with a “Diagnose soon” driveability rating: Low severity - the car is safe to drive - but fix it before your emissions test, since this code is an automatic failure. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
failed emissions test
slight decrease in fuel efficiency
fuel smell
abnormal fuel filling - slow fill-ups or the pump clicking off early
Likely causes
Corroded, damaged, or shorted wiring in the sensor harness (most common)
Defective EVAP fuel vapor temperature sensor
Corroded, melted, or broken connector pins
Excessive resistance in the circuit
Obstruction or leak in the EVAP plumbing
ECM issue (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Locate the fuel vapor temperature sensor and inspect its connector for corrosion, melting, or a broken lock tab, plus the harness for rubbing or bare wires. Tests: Defective EVAP fuel vapor temperature sensor
Repair any wiring or connector damage, clear the code, and see if it returns. Tests: Corroded, melted, or broken connector pins
If it returns, test the sensor voltage and ground circuits with a multimeter per the factory pin-out procedure. Tests: Excessive resistance in the circuit
Inspect the EVAP plumbing for obstructions or leaks that could skew the sensor reading. Tests: Obstruction or leak in the EVAP plumbing
Test the sensor itself against the factory specs and replace it if it fails.
Only suspect the ECM after the sensor, wiring, and plumbing are all proven good.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $200
Labor$100 – $300
Wiring repair or EVAP fuel vapor temperature sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2026 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Most of this is under-car inspection of wiring and plastic lines; be gentle with brittle EVAP lines, which crack easily when disturbed.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →