P0AB9

P0AB9 on a 2008–2009 GMC Yukon Hybrid: Hybrid/EV system performance

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0AB9 on a 2008–2009 GMC Yukon Hybrid · 2024–2025 Mazda CX-90

DIY difficulty 4/5

This is a fault in the car's high-voltage hybrid system (the part not doing its job the way it should). High voltage can kill, so the rule for all of these codes is the same: check the 12V battery, fuses, and connectors you can reach, and leave everything on the orange cables and inside the pack to a qualified technician.

Key facts

☑ Before you buy parts — check these first:
On your 2008–2009 GMC Yukon Hybrid (6.0L V8) — Aux pump control module (bump/jerk + autostop stall): Factory-documented
The control module lives under the 12V battery in the front of the engine bay. A DIY-capable owner can swap the module and harnesses in under two hours, but the harness work is fiddly pigtail splicing, not plug-and-play.
Do this test first: Start with high-voltage safety: the traction battery and its orange cables carry voltage high enough to kill. Never open the pack or probe HV connectors yourself — DIY on this code means the 12V system, fuses, and accessible low-voltage connectors only.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0AB9 on the 2008–2009 GMC Yukon Hybrid — but the community-sourced Aux pump control module (bump/jerk + autostop stall) note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: owner forum · owner forum · GM PIP / NHTSA TSB PDF

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Start with high-voltage safety: the traction battery and its orange cables carry voltage high enough to kill. Never open the pack or probe HV connectors yourself — DIY on this code means the 12V system, fuses, and accessible low-voltage connectors only. Tests: wiring or connector fault
  2. Check the 12V battery's health and terminal connections — a weak 12V battery is a classic cause of phantom hybrid codes.
  3. Check the fuses feeding the hybrid control system.
  4. Inspect accessible low-voltage connectors in the area for corrosion or loose pins. Tests: wiring or connector fault
  5. Scan hybrid live data and freeze-frame data around the code for clues.
  6. Anything on the orange cables or inside the pack is technician-only.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2008–2009 GMC Yukon Hybrid: Aux pump control module (bump/jerk + autostop stall) — test first, then buy for this job.
The price range below is a national planning range for P0AB9 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$100 – $3000
Labor$450 – $2400

system component drift. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0AB9 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

4 of 5 — Mostly a shop job: you can check the 12V battery, fuses, and accessible connectors, but high-voltage diagnosis is technician-only.

Watch this repair on YouTube

Parts & tools

Battery & charging toolkit — what the job actually takes

Torque specs: Terminal clamps: snug, typically 5–8 Nm. Over-tightening cracks the battery post.

Pro tip: Disconnect negative first, reconnect negative last. On module-heavy cars use a memory saver so you don’t lose radio codes and adaptations.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →