P0A1B

P0A1B on a 2013–2016 Fiat 500e: Drive motor A control module performance

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0A1B on a 2013–2016 Fiat 500e

DIY difficulty 4/5

The electric drive motor is fed by high-voltage cables straight from the battery. This code means the computer got the part not doing its job the way it should from the motor or one of its sensors. The motor and its orange cables carry lethal voltage, so this stays a professional repair — you can still check the 12V battery and the connectors you can reach.

Key facts

☑ Before you buy parts — check these first:
On your 2013–2016 Fiat 500e (all) — PIM voltage-transient propulsion-shutdown recall (S26 / 16V303): Factory-documented
Free dealer recall. No parts: it is a software/calibration remedy. If your car already threw P1AEE or P0A1B, tell the studio so they can confirm the fix clears it.
Do this test first: Park, power down completely, and respect the high-voltage system: the battery pack and orange cables are lethal to touch. Leave anything inside the pack to a trained technician; you can safely check the 12V battery, fuses, and connectors outside the pack.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0A1B on the 2013–2016 Fiat 500e — but the community-sourced PIM voltage-transient propulsion-shutdown recall (S26 / 16V303) note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Tips

Sources: NHTSA Part 573 report — 16V303000 (P1AEE/P0A1B, 16,549 cars) · recall history (16V303, PIM voltage spikes, propulsion shutdown)

Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Park, power down completely, and respect the high-voltage system: the battery pack and orange cables are lethal to touch. Leave anything inside the pack to a trained technician; you can safely check the 12V battery, fuses, and connectors outside the pack.
  2. Check the 12V battery's health and terminal connections — a weak 12V battery is a classic cause of phantom hybrid codes.
  3. Inspect the motor's low-voltage sensor connectors for corrosion, damage, or loose pins — hands off the orange HV cables.
  4. Look for companion codes: position, current, and temperature sensor codes together point at a shared harness problem.
  5. With live data running, gently wiggle-test the sensor harness to catch intermittents.
  6. Motor or resolver replacement is high-voltage work — technician-only.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2013–2016 Fiat 500e: PIM voltage-transient propulsion-shutdown recall (S26 / 16V303) — test first, then buy for this job.
The price range below is a national planning range for P0A1B on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$100 – $2000
Labor$450 – $1800

internal module fault. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0A1B ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

4 of 5 — Mostly a shop job: you can check the 12V battery, fuses, and accessible connectors, but high-voltage diagnosis is technician-only.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →