P0847

P0847 on a 2001–2004 GMC Sierra HD: Transmission fluid pressure sensor/switch B circuit low

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0847 on a 2001–2004 GMC Sierra HD

DIY difficulty 4/5

Your transmission's B pressure sensor is reading too low - usually a shorted wire. The computer may overcompensate with harsh, slamming shifts.

Key facts

☑ Before you buy parts — check these first:
On your 2001–2004 GMC Sierra HD (6.6L LB7 Duramax V8 diesel, 8.1L Vortec V8) — Allison NSBU (neutral start backup) switch failure - blank/flashing PRNDL: Factory-documented
Updated tan switch from any Allison distributor or GM dealer; YouTube walkthroughs cover the 2001-2004 replacement.
Do this test first: Check for TSBs and companion codes; diagnose power faults first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0847 on the 2001–2004 GMC Sierra HD — but the community-sourced Allison NSBU (neutral start backup) switch failure - blank/flashing PRNDL note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: ThumperTalk: GM bulletin 02-07-30-011C text (NSBU, 2001-2004 Sierra/Allison) · TheDieselPageForums: PRNDL problem fixed (NSBU black vs tan switch) · YouTube: Allison NSBU replacement (2001-2004 Duramax/8.1)

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check for TSBs and companion codes; diagnose power faults first.
  2. Check fluid level and condition.
  3. Inspect the sensor connector and transmission harness for chafing, corrosion, and pin damage. Tests: Chafed harness at the transmission case
  4. Disconnect the sensor and see if the low signal clears - if it does, the sensor is the short.
  5. With power removed, test the signal wire for continuity to ground; repair the shorted section.
  6. Clear the code and confirm the pressure reading responds normally on live data.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2001–2004 GMC Sierra HD: Allison NSBU (neutral start backup) switch failure - blank/flashing PRNDL — test first, then buy for this job.
The price range below is a national planning range for P0847 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$80 – $350
Labor$200 – $500

Transmission fluid pressure sensor/switch replacement or shorted-wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0847 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

4 of 5 — Connector inspection first - the sensor itself is often under the pan.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: Sensor mounting bolts: typically 8–12 Nm — verify spec. Never overtighten sensors with plastic bodies.

Pro tip: Check wiring and connectors first — chafed wires and corroded pins cause more sensor codes than dead sensors do.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →