Diagnose soonMaximum-pressure failsafe shifting bangs the drivetrain - get it diagnosed before it beats up the transmission.
Your transmission's A pressure sensor is reading too low - usually a shorted wire. The computer may overcompensate with harsh, slamming shifts.
Key facts
P0842 means transmission fluid pressure sensor/switch A circuit low. Your transmission's A pressure sensor is reading too low - usually a shorted wire. The computer may overcompensate with harsh, slamming shifts. WrenchFair's published fair-price range for this repair is $80–$350 parts and $200–$500 labor at independent shops.
WrenchFair rates P0842 a 4-of-5 DIY difficulty (“Connector inspection first - the sensor itself is often under the pan.”) with a “Diagnose soon” driveability rating: Maximum-pressure failsafe shifting bangs the drivetrain - get it diagnosed before it beats up the transmission. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2019–2020 Subaru Ascent (2.4L turbo FA24DIT) — CVT chain slip — WUV-07 and WRK-21 recalls:Factory-documented
Dealer service only — there is no owner-servicable fix for a slipping CVT chain. The DIY angle is knowing the campaigns exist before buying or before a failure strands you.
Do this test first: Check for TSBs and companion codes; diagnose power faults first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0842 on the 2019–2020 Subaru Ascent — but the community-sourced CVT chain slip — WUV-07 and WRK-21 recalls note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Transmission components: verify — No owner-published torque values for this dealer-only recall — confirm against factory service info.
Tips
Two stacked recalls cover this on the early Ascents — WUV-07 (NHTSA 19V-855, ~76,800 2019 cars) for the hydraulic pressure sensor reading high and loosening chain tension, then WRK-21 (NHTSA 21V-955, ~198,000 2019-2020 Ascents plus 2020 Legacy/Outback) for a TCU programming error that let the chain slip and break its guide. Even if WUV-07 was done, cars must return for WRK-21.
Symptoms owners report: irregular noises, hesitation, vibration, or a malfunction indicator lamp — and eventually loss of drive power if the chain keeps slipping and breaks the guide.
The remedy is free: TCU reprogramming, hydraulic-sensor harness replacement on cars with stored slip codes, and full transmission replacement if low chain tension damage is confirmed. Subaru also extended the powertrain warranty on affected cars to 10 years / 100,000 miles specifically for CVT chain slip.
Shopping tip: a 2019-2020 Ascent with documented recall completion and no slip symptoms is a very different vehicle than an unrepaired early build — check the VIN against both campaigns before buying.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
harsh, slamming shifts
limp mode
check-engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Signal wire shorted to ground (most common)
Failed pressure sensor/switch A stuck low 3 owner notes link this repair to P0842
Corroded connector bridging the signal to ground
Chafed harness at the transmission case
Failed PCM/TCM (rare)
Owner notes linked to P0842: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for TSBs and companion codes; diagnose power faults first.
Check fluid level and condition.
Inspect the sensor connector and transmission harness for chafing, corrosion, and pin damage. Tests: Chafed harness at the transmission case
Disconnect the sensor and see if the low signal clears - if it does, the sensor is the short.
With power removed, test the signal wire for continuity to ground; repair the shorted section.
Clear the code and confirm the pressure reading responds normally on live data.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2019–2020 Subaru Ascent: CVT chain slip — WUV-07 and WRK-21 recalls — test first, then buy for this job.
The price range below is a national planning range for P0842 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$80 – $350
Labor$200 – $500
Transmission fluid pressure sensor/switch replacement or shorted-wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0842 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Connector inspection first - the sensor itself is often under the pan.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →