Diagnose soonMaximum-pressure failsafe shifting bangs the drivetrain - get it diagnosed before it beats up the transmission.
Your transmission's A pressure sensor is reading too low - usually a shorted wire. The computer may overcompensate with harsh, slamming shifts.
Key facts
P0842 means transmission fluid pressure sensor/switch A circuit low. Your transmission's A pressure sensor is reading too low - usually a shorted wire. The computer may overcompensate with harsh, slamming shifts. WrenchFair's published fair-price range for this repair is $80–$350 parts and $200–$500 labor at independent shops.
WrenchFair rates P0842 a 4-of-5 DIY difficulty (“Connector inspection first - the sensor itself is often under the pan.”) with a “Diagnose soon” driveability rating: Maximum-pressure failsafe shifting bangs the drivetrain - get it diagnosed before it beats up the transmission. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2009–2010 Chevrolet Traverse (3.6L V6) — 6T75 3-5-R wave plate failure — no reverse, harsh 3rd/5th:Owner-verified
Internal transmission repair — the wave plate lives deep inside the 6T75 case, so this means transmission removal and a full teardown. A rebuild shop or dealer job for nearly everyone; the DIY value here is in diagnosis and not being sold the wrong fix.
Do this test first: Check for TSBs and companion codes; diagnose power faults first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0842 on the 2009–2010 Chevrolet Traverse — but the community-sourced 6T75 3-5-R wave plate failure — no reverse, harsh 3rd/5th note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Internal components: verify — Internal transmission fasteners — confirm against factory service info; not confirmed from owner sources.
Tips
The classic signature: no reverse, slipping or harsh shifting only between 3rd and 5th gears, with P0776 and P0842 codes. GM documents it as TSB PIP4627A / 09-07-30-012B — a broken 35R clutch wave plate.
When the plate breaks, the 35R piston leaks and can't apply properly, so only 3rd, 5th, and reverse are affected — if all gears are misbehaving, suspect something else first.
GM extended transmission coverage for this condition on affected VINs; check with a dealer before paying out of pocket.
Owner-reported costs run roughly $2,000-$4,000 for a wave-plate repair or rebuild ($3,200-$3,700 reported for full overhauls). During a rebuild, the replacement wave plate must be installed with the rounded edge of its internal splines facing the 35R piston, or the failure repeats.
A harsh 2-3 shift or cruise-control 'busyness' on a 2009 alone may just need the TCM re-flash in PIP4668 — cheaper than any teardown.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
harsh, slamming shifts
limp mode
check-engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Signal wire shorted to ground (most common)
Failed pressure sensor/switch A stuck low 3 owner notes link this repair to P0842
Corroded connector bridging the signal to ground
Chafed harness at the transmission case
Failed PCM/TCM (rare)
Owner notes linked to P0842: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for TSBs and companion codes; diagnose power faults first.
Check fluid level and condition.
Inspect the sensor connector and transmission harness for chafing, corrosion, and pin damage. Tests: Chafed harness at the transmission case
Disconnect the sensor and see if the low signal clears - if it does, the sensor is the short.
With power removed, test the signal wire for continuity to ground; repair the shorted section.
Clear the code and confirm the pressure reading responds normally on live data.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2009–2010 Chevrolet Traverse: 6T75 3-5-R wave plate failure — no reverse, harsh 3rd/5th — test first, then buy for this job.
The price range below is a national planning range for P0842 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$80 – $350
Labor$200 – $500
Transmission fluid pressure sensor/switch replacement or shorted-wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0842 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Connector inspection first - the sensor itself is often under the pan.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →