P0840

P0840 on a 2007–2007 Nissan Maxima: Transmission fluid pressure sensor/switch A circuit

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0840 on a 2007–2007 Nissan Maxima · 2007–2017 Nissan Versa

DIY difficulty 4/5

One of your transmission's pressure sensors (the 'A' one) has an electrical fault. Expect changed shift feel and possibly limp mode.

Key facts

☑ Before you buy parts — check these first:
On your 2007–2007 Nissan Maxima (3.5L V6 (VQ35DE)) — MIL on with P0840/P0845 - CVT pressure sensor (NTB08-042): Factory-documented
Dealer or well-equipped DIY (TCM-level scan needed to confirm the code; sensor is accessible once diagnosed).
Do this test first: Check for TSBs and companion power or pressure codes - diagnose power faults and multi-sensor codes first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0840 on the 2007–2007 Nissan Maxima — but the community-sourced MIL on with P0840/P0845 - CVT pressure sensor (NTB08-042) note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Tips

Sources: Yumpu - NTB08-042 bulletin text (2007 Maxima MIL on with P0840 or P0845; replace primary/secondary oil pressure sensor assembly) · NHTSA manufacturer communications index - 2007 Maxima (NTB08-042 listed among model-year bulletins)

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0840: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check for TSBs and companion power or pressure codes - diagnose power faults and multi-sensor codes first. Tests: Failed transmission fluid pressure sensor/switch A
  2. Check fluid level and condition; burnt fluid or debris points to internal problems. Tests: Internal transmission problems - leaks, stuck valve, low line pressure
  3. Locate the TFPS 'A' and inspect its connector and wiring for corrosion, rubbing, and burn spots - external connector corrosion is the most common cause. Tests: Corroded or damaged external connector at the transmission (most common)
  4. Clear the code after cleaning the connector; if it returns, test circuit power, ground, and signal. Tests: Corroded or damaged external connector at the transmission (most common)
  5. Test the sensor against factory specs; replace it if it fails.
  6. If sensor and circuit test good, suspect internal leaks, a stuck valve, or low line pressure.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2007–2007 Nissan Maxima: MIL on with P0840/P0845 - CVT pressure sensor (NTB08-042) — test first, then buy for this job.
The price range below is a national planning range for P0840 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$80 – $350
Labor$200 – $500

Transmission fluid pressure sensor/switch replacement (often requires pan removal). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0840 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

4 of 5 — Connector inspection is easy; the sensor itself is often inside the pan on the valve body.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: Sensor mounting bolts: typically 8–12 Nm — verify spec. Never overtighten sensors with plastic bodies.

Pro tip: Check wiring and connectors first — chafed wires and corroded pins cause more sensor codes than dead sensors do.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →