Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA no-start that strikes at random is more than annoying - track down the short before it strands you.
Your clutch switch A is reading too low - usually a shorted wire. Most likely outcome: you turn the key and nothing happens.
Key facts
P0831 means clutch pedal switch A circuit low. Your clutch switch A is reading too low - usually a shorted wire. Most likely outcome: you turn the key and nothing happens. WrenchFair's published fair-price range for this repair is $25–$120 parts and $80–$200 labor at independent shops.
WrenchFair rates P0831 a 2-of-5 DIY difficulty (“Short-to-ground tracing is methodical multimeter work on a small under-dash circuit.”) with a “Diagnose soon” driveability rating: A no-start that strikes at random is more than annoying - track down the short before it strands you. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
engine will not crank
check-engine light on
no other symptoms besides the no-start
Likely causes
Wiring shorted to ground in the switch A circuit (most common)
Failed clutch pedal switch A stuck in the low state
Corroded connector bridging the signal to ground
Pinched harness at the firewall or pedal bracket
Failed PCM (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Look up TSBs for the year, make, and model matching this code.
Inspect the pedal-bracket harness for pinched or chafed spots, especially at the firewall pass-through. Tests: Pinched harness at the firewall or pedal bracket
Disconnect switch A and see if the low signal clears - if it does, the switch itself is the short.
With power removed, test the signal wire for continuity to ground and repair the shorted section. Tests: Wiring shorted to ground in the switch A circuit (most common)
Check connectors for corrosion or pins bridging the signal to ground.
Clear the code and confirm the engine cranks only with the clutch pressed.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$25 – $120
Labor$80 – $200
Clutch pedal switch A replacement or shorted-wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0831 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Short-to-ground tracing is methodical multimeter work on a small under-dash circuit.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →