P0819: Up and down shift switch to transmission range correlation
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Drive safeManual shifting may be dead, but the transmission still shifts itself normally - fix it when convenient.
Your paddle shifters and the gear selector are telling the computer two different stories. Manual shifting may be disabled or the gear display may be wrong; automatic mode still works.
Key facts
P0819 means up and down shift switch to transmission range correlation. Your paddle shifters and the gear selector are telling the computer two different stories. Manual shifting may be disabled or the gear display may be wrong; automatic mode still works. WrenchFair's published fair-price range for this repair is $60–$300 parts and $100–$250 labor at independent shops.
WrenchFair rates P0819 a 3-of-5 DIY difficulty (“Two switches to check instead of one, but both test the same way with a multimeter.”) with a “Drive safe” driveability rating: Manual shifting may be dead, but the transmission still shifts itself normally - fix it when convenient. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
manual upshift/downshift function disabled
gear indicator shows the wrong gear
paddle inputs ignored by the transmission
Likely causes
Failed upshift or downshift paddle/tap-shift switch (most common)
Failed transmission range sensor
Open or shorted wiring in either switch circuit (often the clockspring on steering-wheel paddles)
Corroded connector at a switch or the range sensor
Faulty PCM or programming error (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Try the paddles/tap-shift in manual mode and note exactly which direction fails, then compare against the dash gear indicator. Tests: Failed upshift or downshift paddle/tap-shift switch (most common)
Look up TSBs for the year, make, and model matching this code.
Test voltage, ground, and signal at the upshift/downshift switches through their press-and-release cycles. Tests: Failed upshift or downshift paddle/tap-shift switch (most common)
Test the transmission range switch output in every shifter detent and compare with the scan-tool gear reading. Tests: Failed transmission range sensor
Inspect shared wiring and connectors - especially the steering-wheel clockspring on paddle-equipped cars.
Replace whichever switch fails factory specs, clear the code, and confirm manual shifting tracks the indicator.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $300
Labor$100 – $250
Upshift/downshift switch or transmission range sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0819 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Two switches to check instead of one, but both test the same way with a multimeter.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →