P0809: Clutch position sensor A circuit intermittent
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonAn intermittent clutch signal can stall the engine or strand you without warning - track it down before it picks the time and place.
Your clutch pedal switch works most of the time but cuts out randomly - expect the occasional no-start or the engine dying when you press the clutch, then everything works again.
Key facts
P0809 means clutch position sensor A circuit intermittent. Your clutch pedal switch works most of the time but cuts out randomly - expect the occasional no-start or the engine dying when you press the clutch, then everything works again. WrenchFair's published fair-price range for this repair is $25–$120 parts and $100–$250 labor at independent shops.
WrenchFair rates P0809 a 3-of-5 DIY difficulty (“Intermittents are found by wiggle-testing the harness while watching live data - patience, not parts, fixes these.”) with a “Diagnose soon” driveability rating: An intermittent clutch signal can stall the engine or strand you without warning - track it down before it picks the time and place. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
intermittent no-start
engine stumbles or stalls when the clutch is pressed
check-engine light that comes and goes
cruise control cutting out randomly
Likely causes
Loose, corroded, or spread connector pin at the sensor or control module (most common)
Chafed wiring that only shorts or opens when the harness flexes
Failing clutch position sensor with an internal intermittent break
Loose control-module ground strap
Failing PCM/TCM (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Look up TSBs for the year, make, and model matching this code.
Graph the clutch position sensor signal on the scan tool while wiggling the harness, tapping the sensor, and working the pedal - watch for dropouts. Tests: Failing clutch position sensor with an internal intermittent break
Inspect every connector in the circuit for corrosion, spread pins, and weak terminal tension; clean and re-tension as needed. Tests: Loose, corroded, or spread connector pin at the sensor or control module (most common)
Check the control-module ground straps for looseness or corrosion. Tests: Loose control-module ground strap
Flex-test the wiring where it passes through the firewall and around the pedal bracket, feeling for internal wire breaks.
Only replace the sensor if the wiggle test isolates the dropout to the sensor itself.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$25 – $120
Labor$100 – $250
Connector repair or clutch position sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0809 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Intermittents are found by wiggle-testing the harness while watching live data - patience, not parts, fixes these.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →