P0806: Clutch position sensor A circuit range/performance
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA drifting clutch signal can turn into a no-start at the worst moment - check it before it strands you.
Your clutch pedal switch works electrically, but the reading it sends does not add up. Expect starting quirks - like needing to pump the pedal - or the check-engine light with no obvious problem.
Key facts
P0806 means clutch position sensor A circuit range/performance. Your clutch pedal switch works electrically, but the reading it sends does not add up. Expect starting quirks - like needing to pump the pedal - or the check-engine light with no obvious problem. WrenchFair's published fair-price range for this repair is $25–$120 parts and $80–$180 labor at independent shops.
WrenchFair rates P0806 a 2-of-5 DIY difficulty (“Often fixed by adjusting or replacing the pedal switch - both are under-dash jobs a DIYer can handle.”) with a “Diagnose soon” driveability rating: A drifting clutch signal can turn into a no-start at the worst moment - check it before it strands you. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
engine cranks only if the clutch pedal is pressed extra hard
intermittent no-start
check-engine light with no other symptoms
cruise control dropping out unexpectedly (on cars that use the clutch switch for cruise cancel)
Likely causes
Clutch position sensor out of adjustment or misaligned on the pedal bracket (most common)
Worn or failing clutch position sensor giving a weak or drifting signal
Corroded or loose connector adding resistance to the circuit
Damaged wiring with partial chafing or intermittent contact
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Look up TSBs for the year, make, and model matching this code.
Use scan-tool live data to watch the clutch position sensor state while slowly pressing and releasing the pedal - look for flickering or a dead zone. Tests: Clutch position sensor out of adjustment or misaligned on the pedal bracket (most common)
Check the switch adjustment and mounting on the pedal bracket; reposition per factory spec if it is out of alignment. Tests: Clutch position sensor out of adjustment or misaligned on the pedal bracket (most common)
Inspect connectors and wiring for corrosion or partial damage that could skew the signal. Tests: Damaged wiring with partial chafing or intermittent contact
Test the sensor's signal output against factory specifications; replace the sensor if the signal is erratic or out of range.
Clear the code, verify clean on/off switching through the full pedal travel, and confirm normal starting.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$25 – $120
Labor$80 – $180
Clutch position sensor adjustment or replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0806 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Often fixed by adjusting or replacing the pedal switch - both are under-dash jobs a DIYer can handle.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →