Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonIf the car can start with the clutch out and in gear, it can lurch unexpectedly - park in neutral and fix this promptly.
The switch that tells your car the clutch pedal is pressed has an electrical problem. The car may refuse to start, or - worse - it might crank with the clutch out and the car in gear.
Key facts
P0805 means clutch position sensor circuit. The switch that tells your car the clutch pedal is pressed has an electrical problem. The car may refuse to start, or - worse - it might crank with the clutch out and the car in gear. WrenchFair's published fair-price range for this repair is $25–$120 parts and $80–$180 labor at independent shops.
WrenchFair rates P0805 a 2-of-5 DIY difficulty (“The switch is under the dash on the pedal bracket - visual inspection and basic multimeter tests find most of these.”) with a “Diagnose soon” driveability rating: If the car can start with the clutch out and in gear, it can lurch unexpectedly - park in neutral and fix this promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
engine will not crank or start
engine cranks and starts without the clutch pressed
check-engine or transmission warning light on
no symptoms besides the light
Likely causes
Failed clutch position sensor/switch (most common)
Damaged, chafed, or shorted wiring in the sensor circuit
Corroded, loose, or damaged connector at the sensor or control module
Blown fuse or fusible link in the circuit (if equipped)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Look up TSBs for the year, make, and model matching this code.
Locate the clutch position switch on the pedal bracket and inspect it and its wiring for physical damage, rubbing, bare wires, or burn spots. Tests: Failed clutch position sensor/switch (most common)
Check connectors and pins for corrosion, looseness, and damage at the switch, control module, starter, and starter solenoid; check the circuit fuse if equipped. Tests: Corroded, loose, or damaged connector at the sensor or control module
With a multimeter, verify power on one side of the switch with the clutch released and on both sides with the clutch pressed. Tests: Failed clutch position sensor/switch (most common)
Test wiring continuity with power removed - any resistance in wiring or ground straps indicates a fault to repair.
Clear the code and verify the starter only cranks with the clutch pedal pressed.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$25 – $120
Labor$80 – $180
Clutch position sensor/switch replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0805 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The switch is under the dash on the pedal bracket - visual inspection and basic multimeter tests find most of these.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →