Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA failed inhibit could let reverse engage while the car is moving forward, which can wreck the transmission - do not ignore this one.
A safety solenoid keeps you from slamming into reverse while rolling forward, and its wiring has a fault. Worst case the shifter could drop into reverse at speed, or you might not get reverse at all.
Key facts
P0801 means reverse inhibit control circuit. A safety solenoid keeps you from slamming into reverse while rolling forward, and its wiring has a fault. Worst case the shifter could drop into reverse at speed, or you might not get reverse at all. WrenchFair's published fair-price range for this repair is $60–$250 parts and $100–$300 labor at independent shops.
WrenchFair rates P0801 a 3-of-5 DIY difficulty (“The solenoid is usually accessible on the transmission, but testing its circuit properly takes a multimeter and the factory wiring chart.”) with a “Diagnose soon” driveability rating: A failed inhibit could let reverse engage while the car is moving forward, which can wreck the transmission - do not ignore this one. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
shifter can be moved into reverse while driving forward
shifter will not go into reverse
blown fuses in transmission control circuits
no symptoms at all
Likely causes
Failed reverse inhibit solenoid (most common)
Open or shorted wiring or connector in the reverse inhibit control circuit
Faulty reverse inhibit sensor (if equipped)
Worn shifter linkage, bushings, or shift pawl interfering with the inhibit mechanism
Faulty control module or programming error (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check and replace any blown fuses in the transmission control circuits first - a shorted solenoid is a common cause. Tests: Open or shorted wiring or connector in the reverse inhibit control circuit
Scan all codes and freeze-frame data, clear, and road-test to confirm the code returns.
Inspect the reverse inhibit solenoid and its wiring for chafing, corrosion, or damage, especially where the harness flexes near the transmission. Tests: Failed reverse inhibit solenoid (most common)
Test power and ground at the solenoid, then test the solenoid itself against factory specifications. Tests: Failed reverse inhibit solenoid (most common)
Check shifter linkage and bushings for wear that could fight the inhibit mechanism.
Use voltage-drop testing on the control and signal circuits back to the control module before suspecting the module.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $250
Labor$100 – $300
Reverse inhibit solenoid replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0801 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The solenoid is usually accessible on the transmission, but testing its circuit properly takes a multimeter and the factory wiring chart.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →