P07B3: Transmission Park Position Sensor/Switch A Circuit Low
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA car that cannot confirm park is a rollaway risk - use the parking brake and fix soon.
Your transmission double-checks that it is really in park before letting you start, and sensor A stuck unusually low. The car may refuse to start or not recognize park. Check the switch, its adjustment, and wiring.
Key facts
P07B3 means transmission Park Position Sensor/Switch A Circuit Low. Your transmission double-checks that it is really in park before letting you start, and sensor A stuck unusually low. The car may refuse to start or not recognize park. Check the switch, its adjustment, and wiring. WrenchFair's published fair-price range for this repair is $40–$200 parts and $100–$300 labor at independent shops.
WrenchFair rates P07B3 a 2-of-5 DIY difficulty (“Switch adjustment matters; check with a scan tool.”) with a “Diagnose soon” driveability rating: A car that cannot confirm park is a rollaway risk - use the parking brake and fix soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
no-start
car does not recognize park
check engine light on
Likely causes
failed park position switch A
misadjusted switch
wiring fault
corroded connector
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Watch the park signal while shifting in and out of park.
Check switch A adjustment and wiring.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $200
Labor$100 – $300
Park position switch replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P07B3 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Switch adjustment matters; check with a scan tool.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →