Your output speed sensor is reporting the wrong direction of travel. Check that the sensor is the correct part, properly seated, and its wiring is sound.
Key facts
P077B means output Shaft Speed Sensor Circuit - Direction Error. Your output speed sensor is reporting the wrong direction of travel. Check that the sensor is the correct part, properly seated, and its wiring is sound. WrenchFair's published fair-price range for this repair is $40–$150 parts and $100–$300 labor at independent shops.
WrenchFair rates P077B a 2-of-5 DIY difficulty (“Verify correct part and installation.”) with a “Diagnose soon” driveability rating: Drivable; fix soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2008–2013 Chevrolet Tahoe Hybrid (6.0L V8) — No-start diagnosis (no conventional starter):Owner-verified
Diagnostic only: use a hybrid-aware scan tool and a helper to watch the crankshaft pulley. Do not touch high-voltage hardware for this test.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P077B on the 2008–2013 Chevrolet Tahoe Hybrid — but the community-sourced No-start diagnosis (no conventional starter) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Diagnostic fasteners (covers, disconnect): verify — No torque values involved in this diagnostic note.
Tips
Remember there is no conventional 12V starter to fail: the two motor-generators inside the 2ML70 crank the engine through the crankshaft at about 1500 rpm. If you hear nothing from under the hood during a no-start, think hybrid system, not starter motor.
Do the eyeball test: have someone attempt a start while you watch the crankshaft pulley. If the crank is actually spinning and it will not fire, the fault is ignition or fuel, not hybrid. If the crank is not moving, suspect the transmission input/output shaft side.
Pull the matching codes: P16F3, P2160, P077B, and P0722 point at the transmission-side start and speed signals on these trucks.
After any hybrid service work, reseat the orange high-voltage service disconnect on the pack until it gives its full two-step click — a half-seated disconnect is a common no-start cause — and confirm the underhood inverter cover is back on, since a missing cover triggers the interlock and blocks start.
Clearing codes with a generic scanner is not enough after a hybrid shutdown; the dealer needs to run a full computer reset (about an hour) or the shutdown can recur.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Typical time: “Clearing codes with a generic scanner is not enough after a hybrid shutdown; the dealer needs to run a full computer reset (about an hour) or the shutdown can recur.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
hill-hold misbehaving
harsh shifts
check engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
incorrect or misinstalled sensor
wiring fault
damaged reluctor wheel
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Verify the sensor part number and seating.
Check the wiring and reluctor. Tests: damaged reluctor wheel
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2008–2013 Chevrolet Tahoe Hybrid: No-start diagnosis (no conventional starter) — test first, then buy for this job.
The price range below is a national planning range for P077B on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $150
Labor$100 – $300
Output speed sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P077B ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →