Diagnose soonTransmission may shift poorly. Drive gently and diagnose soon.
A second pressure-regulating solenoid is stuck or underperforming. The transmission can't control clutch pressure properly, so shifts slip or bang.
Model notes: A solenoid that tests fine electrically but can't control pressure has either a stuck valve or a worn bore - the hydraulic side, not the electrical side.
Key facts
P0776 means pressure control solenoid B performance/stuck off. A second pressure-regulating solenoid is stuck or underperforming. The transmission can't control clutch pressure properly, so shifts slip or bang. WrenchFair's published fair-price range for this repair is $50–$200 parts and $200–$600 labor at independent shops.
WrenchFair rates P0776 a 4-of-5 DIY difficulty (“Performance codes need hydraulic diagnosis, not just resistance checks.”) with a “Diagnose soon” driveability rating: Transmission may shift poorly. Drive gently and diagnose soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2007–2009 GMC Acadia (3.6L V6) — 3-5-R wave plate failure (no reverse, 3rd/5th flare):Owner-verified
Transmission-out job — the 3-5-R clutch wave plate lives inside the 6T70/6T75 case. Diagnosis is the DIY-friendly part; the repair is a transmission rebuild or replacement best left to a specialist.
Do this test first: Check fluid condition - debris points at internal wear beyond the solenoid
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0776 on the 2007–2009 GMC Acadia — but the community-sourced 3-5-R wave plate failure (no reverse, 3rd/5th flare) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Transmission internal fasteners: verify — Specialist rebuild — no owner-documented torque specs; confirm against factory service info.
Tips
Learn the pattern: SES light plus no reverse, and/or a slip/flare or harsh shift in 3rd and 5th gears. The classic DTC is P0776 (clutch pressure control solenoid 2 stuck off); P0777, P2723, P0717, P0716, P2715, and P2714 can set from the same failure.
The cause per GM bulletin 09-07-30-012B is a broken 3-5-R (35R) clutch wave plate that lets the apply piston over-stroke and leak — typically not before about 20,000 miles. Debris from the breakage can also foul the speed sensors and other clutches.
The documented fix is the updated waved clutch plate (P/N 24254103) with a full cleanup: debris cleaned from the whole transmission, plus a new pump fluid filter and control-solenoid filter plate. Skipping the cleanup is how repeat failures happen.
One owner caught it early and had a dealer rebuild for under $1,500 with GM assistance — so stop driving it the moment reverse disappears or 3rd/5th starts flaring, and call a dealer about goodwill help before authorizing a $4,000-$5,000 replacement.
If a shop does the rebuild, the plate's installation orientation matters (GM guidance: rounded edge of the internal splines toward the 35R piston) to prevent a repeat failure.
A full replacement transmission is the common outcome once debris has circulated — multiple owners report reman units after the wave plate disintegrated, so early diagnosis genuinely saves money here.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
slipping shifts
harsh engagement
check engine light
limp mode
transmission overheating
poor fuel economy
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Sticking pressure control solenoid B (most common)
Contaminated fluid
Valve body bore wear
Electrical fault in the solenoid circuit
Owner notes linked to P0776: 5 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check fluid condition - debris points at internal wear beyond the solenoid Tests: Sticking pressure control solenoid B (most common)
Test solenoid resistance and command it with a scan tool while monitoring pressure Tests: Sticking pressure control solenoid B (most common)
If the solenoid tests good electrically but pressure doesn't respond, suspect valve body bore wear Tests: Valve body bore wear
Replace the solenoid; if bore wear is found, the valve body needs professional attention Tests: Valve body bore wear
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2009 GMC Acadia: 3-5-R wave plate failure (no reverse, 3rd/5th flare) — test first, then buy for this job.
The price range below is a national planning range for P0776 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$50 – $200
Labor$200 – $600
Solenoid replacement; pan-accessible on many transmissions. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0776 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Performance codes need hydraulic diagnosis, not just resistance checks.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →