Diagnose soonLimp mode is protective - diagnose before driving far.
Your transmission picks gears with electric shift valves, and solenoid A is stuck on. Expect wrong or missing gears, or limp mode. Check the fluid level first, then test the solenoid.
Key facts
P0752 means shift Solenoid A Stuck On. Your transmission picks gears with electric shift valves, and solenoid A is stuck on. Expect wrong or missing gears, or limp mode. Check the fluid level first, then test the solenoid. WrenchFair's published fair-price range for this repair is $60–$400 parts and $200–$500 labor at independent shops.
WrenchFair rates P0752 a 3-of-5 DIY difficulty (“Solenoids are in the pan on the valve body; a fluid and filter service is often done at the same time.”) with a “Diagnose soon” driveability rating: Limp mode is protective - diagnose before driving far. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2019–2023 Ford Ranger (2.3L EcoBoost + 10R80 (2019-2023)) — 10R80 harsh/delayed shifts — CDF drum bushing slip (TSB 22-2428):Owner-verified
Check your VIN for Ford TSB 22-2428 coverage at the dealer (10R80 built on or before 15-Aug-2022) before authorizing any transmission work. A Ford scan tool or FORScan with a good OBD adapter can pull the transmission-specific codes the TSB lists.
Do this test first: Check the fluid level and condition.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0752 on the 2019–2023 Ford Ranger — but the community-sourced 10R80 harsh/delayed shifts — CDF drum bushing slip (TSB 22-2428) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
The known mechanical failure behind persistent 10R80 harshness is the CDF clutch drum bushing walking out of position and blocking hydraulic passages. Tells: harsh engagement, delayed engagement, harsh or delayed shifts, often with no check-engine light — the failure codes (P0751/P0752/P2700 family) live in the transmission module, not the engine PCM.
Ford's TSB 22-2428 covers 2019-2023 Rangers with a 10R80 built on or before 15-Aug-2022 and prescribes a main-control overhaul with the updated drum design plus Mercon ULV fluid. If your truck's harshness survives a fluid-level check and an adaptive-tables reset, this is the documented next step — not another reset.
Distinguished from the Mustang run's 10R80 note, which covers the adaptive-learning/fluid-level/TSB-18-2119 ladder. The CDF drum is a separate, deeper mechanical failure: owners report that repeated resets and even valve-body swaps did not fix it, while the revised drum did.
Honest caveat: this is transmission-out work, not a driveway job. The value is knowing the documented root cause before paying for repeated software attempts — several owners burned money on reflashes that never addressed the bushing.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
wrong gear
missing gears
limp mode
harsh shifts
check engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
failed shift solenoid A
low or contaminated fluid
wiring fault
valve body fault
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check the fluid level and condition.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Test solenoid A's resistance. Tests: failed shift solenoid A
Inspect the wiring. Replace the solenoid if it tests bad. Tests: failed shift solenoid A
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2019–2023 Ford Ranger: 10R80 harsh/delayed shifts — CDF drum bushing slip (TSB 22-2428) — test first, then buy for this job.
The price range below is a national planning range for P0752 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$60 – $400
Labor$200 – $500
Shift solenoid A replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0752 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Solenoids are in the pan on the valve body; a fluid and filter service is often done at the same time.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →