P0746

P0746 on a 2007–2014 Nissan Maxima: Pressure Control Solenoid A Performance/Stuck Off

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0746 on a 2007–2014 Nissan Maxima

DIY difficulty 3/5

Your transmission controls clutch pressure with electric solenoids, and solenoid A is not performing - it may be stuck off or not regulating pressure. Wrong pressure means harsh shifts, slipping, or limp mode. Check the fluid level first, then test the solenoid.

Key facts

☑ Before you buy parts — check these first:
On your 2007–2014 Nissan Maxima (3.5L V6 (VQ35DE)) — CVT fluid type (NS-2 vs NS-3) and P0746/P0868 valve-body faults: Owner-verified
Moderate DIY for a drain-and-fill (correct fluid is critical); valve-body replacement is professional work (replacement units ship with a program disc).
Do this test first: Check the fluid level and condition.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0746 on the 2007–2014 Nissan Maxima — but the community-sourced CVT fluid type (NS-2 vs NS-3) and P0746/P0868 valve-body faults note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Tips

Sources: iFixit - Nissan Maxima CVT answers thread (NS-2 for 2012 and older, NS-3 for 2013+; NEVER standard red ATF; Jatco CVTs die at 100-120k without proper maintenance) · JustAnswer - 2013 Maxima P0746/P0868 thread (CVT valve-body solenoid codes; slow takeoff; replacement valve body ships with program disc; Nissan OE preferred) · JustAnswer - 2014 Maxima CVT jerking thread (shudder means the internal chain/belt is failing and needs replacement; pull codes first)

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check the fluid level and condition.
  2. Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
  3. Test solenoid A's resistance and compare with spec. Tests: failed pressure control solenoid A
  4. Inspect the wiring to the solenoid. Tests: wiring fault to the solenoid

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2007–2014 Nissan Maxima: CVT fluid type (NS-2 vs NS-3) and P0746/P0868 valve-body faults — test first, then buy for this job.
The price range below is a national planning range for P0746 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$80 – $600
Labor$200 – $600

Pressure control solenoid A replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0746 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — The solenoids are inside the pan on the valve body.

Watch this repair on YouTube

Parts & tools

Transmission service toolkit — what the job actually takes

Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.

Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →