P0718: Input/Turbine Shaft Speed Sensor A Circuit Intermittent
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonLimp mode is protective - diagnose before driving far.
Your transmission measures how fast the input shaft spins to control shifts, and that sensor's signal drops out intermittently. Without it the transmission goes into limp mode. Check the sensor and wiring - metal fuzz stuck to the sensor tip is a classic cause.
Key facts
P0718 means input/Turbine Shaft Speed Sensor A Circuit Intermittent. Your transmission measures how fast the input shaft spins to control shifts, and that sensor's signal drops out intermittently. Without it the transmission goes into limp mode. Check the sensor and wiring - metal fuzz stuck to the sensor tip is a classic cause. WrenchFair's published fair-price range for this repair is $40–$150 parts and $100–$300 labor at independent shops.
WrenchFair rates P0718 a 3-of-5 DIY difficulty (“The sensor is on the transmission case; debris on it signals internal wear.”) with a “Diagnose soon” driveability rating: Limp mode is protective - diagnose before driving far. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
limp mode
harsh shifts
no upshift
check engine light on
Likely causes
failed input speed sensor
metal debris on the sensor
wiring fault
corroded connector
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Watch the input speed reading - dropouts or a dead reading confirm it. Tests: failed input speed sensor
Remove the sensor and check for metal debris on the tip. Tests: metal debris on the sensor
Test the wiring.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $150
Labor$100 – $300
Input speed sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0718 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The sensor is on the transmission case; debris on it signals internal wear.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →