P0716

P0716 on a 2007–2009 GMC Acadia: Input/Turbine Shaft Speed Sensor A Circuit Range/Performance

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0716 on a 2007–2009 GMC Acadia

DIY difficulty 3/5

Your transmission measures how fast the input shaft spins to control shifts, and that sensor's signal does not match the expected speed. Without it the transmission goes into limp mode. Check the sensor and wiring - metal fuzz stuck to the sensor tip is a classic cause.

Key facts

☑ Before you buy parts — check these first:
On your 2007–2009 GMC Acadia (3.6L V6) — 3-5-R wave plate failure (no reverse, 3rd/5th flare): Owner-verified
Transmission-out job — the 3-5-R clutch wave plate lives inside the 6T70/6T75 case. Diagnosis is the DIY-friendly part; the repair is a transmission rebuild or replacement best left to a specialist.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0716 on the 2007–2009 GMC Acadia — but the community-sourced 3-5-R wave plate failure (no reverse, 3rd/5th flare) note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: TSB text · owner forum · owner repair data · owner complaints

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
  2. Watch the input speed reading - dropouts or a dead reading confirm it. Tests: failed input speed sensor
  3. Remove the sensor and check for metal debris on the tip. Tests: metal debris on the sensor
  4. Test the wiring.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2007–2009 GMC Acadia: 3-5-R wave plate failure (no reverse, 3rd/5th flare) — test first, then buy for this job.
The price range below is a national planning range for P0716 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $150
Labor$100 – $300

Input speed sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0716 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — The sensor is on the transmission case; debris on it signals internal wear.

Watch this repair on YouTube

Parts & tools

Transmission service toolkit — what the job actually takes

Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.

Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →