Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonDrivable; wrong temperature data shortens transmission life.
Your transmission changes how it shifts based on fluid temperature, and its temperature sensor is reading wrong - does not track actual temperature. That makes shifts harsh or sloppy. The sensor is often inside the transmission on the internal wiring harness.
Key facts
P0711 means transmission Fluid Temperature Sensor A Circuit Range/Performance. Your transmission changes how it shifts based on fluid temperature, and its temperature sensor is reading wrong - does not track actual temperature. That makes shifts harsh or sloppy. The sensor is often inside the transmission on the internal wiring harness. WrenchFair's published fair-price range for this repair is $50–$300 parts and $150–$400 labor at independent shops.
WrenchFair rates P0711 a 3-of-5 DIY difficulty (“The sensor is often inside the pan on the internal harness.”) with a “Diagnose soon” driveability rating: Drivable; wrong temperature data shortens transmission life. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
harsh shifts when cold
slipping feel when hot
limp mode
check engine light on
Likely causes
failed temperature sensor
internal harness fault
wiring fault
corroded connector
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Watch the temperature reading - a stuck or jumpy value confirms it. Tests: failed temperature sensor
Compare with actual fluid temperature. Tests: failed temperature sensor
Inspect the internal harness. Tests: internal harness fault
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $300
Labor$150 – $400
Transmission temperature sensor or internal harness replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0711 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The sensor is often inside the pan on the internal harness.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →