Diagnose soonA lying range sensor can let the car start in gear - fix soon.
The sensor telling your car which gear you picked (P, R, N, D) is reading wrong - stuck unusually high. That can mean no-start, a lying gear display, or starting in the wrong gear. Check the sensor on the transmission and its connector.
Key facts
P0708 means transmission Range Sensor A Circuit High. The sensor telling your car which gear you picked (P, R, N, D) is reading wrong - stuck unusually high. That can mean no-start, a lying gear display, or starting in the wrong gear. Check the sensor on the transmission and its connector. WrenchFair's published fair-price range for this repair is $40–$200 parts and $100–$300 labor at independent shops.
WrenchFair rates P0708 a 2-of-5 DIY difficulty (“The sensor is on the transmission; alignment matters.”) with a “Diagnose soon” driveability rating: A lying range sensor can let the car start in gear - fix soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2001–2004 GMC Sierra HD (6.6L LB7 Duramax V8 diesel, 8.1L Vortec V8) — Allison NSBU (neutral start backup) switch failure - blank/flashing PRNDL:Factory-documented
Updated tan switch from any Allison distributor or GM dealer; YouTube walkthroughs cover the 2001-2004 replacement.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0708 on the 2001–2004 GMC Sierra HD — but the community-sourced Allison NSBU (neutral start backup) switch failure - blank/flashing PRNDL note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
NSBU switch mounting: verify — Electrical switch; snug the mounting nut per the service procedure and confirm the shift linkage alignment.
Tips
On 2001-2004 Sierra HD trucks with the 5-speed Allison 1000, the external NSBU (neutral start backup / park-neutral position) switch is a classic failure. Water spray from the left front tire hits it directly, moisture gets inside, and you get a flashing or blank PRNDL display, no-start, no engagement, or the transmission stuck in a range.
GM documented it in bulletin 02-07-30-011C (Slow or No Engagement, No Start, Blank PRNDL Display, Flashing PRNDL), listing DTCs P0708, P0872, P0847, P0875, P1711, P1713, and U1000 for 2001-2004 Silverado/Sierra with the Allison LCT1000 and the 6.6L Duramax or 8.1L gas engine.
Diagnosis is simple: look at the switch behind the shift linkage on the driver's side of the transmission. The original failure-prone switch is black with two connectors; the revised moisture-resistant replacement is tan. If yours is black, replace it proactively.
The fix is a 30-minute driveway job with no special tools. Get the updated tan switch (Allison part, around $50 from an Allison distributor versus $160+ at the dealer). Clean the connectors thoroughly; melted potting glue in the connector shells is common and must be scraped out with brake cleaner or the new switch will not seat.
Make sure the front and rear splash shields are properly installed afterward; the bulletin calls them essential because the left-front tire is what was soaking the switch in the first place. For 2006+ trucks the module moved inside the cab, so this only applies to the early external-switch trucks.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
no-start in park or neutral
wrong gear shown on the dash
backup lights not working
limp mode
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
failed range sensor
misadjusted range sensor
corroded connector
wiring fault
water in the sensor
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Watch the gear-position reading while moving the shifter.
Check adjustment per the service manual.
Inspect the connector for corrosion. Tests: corroded connector
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2001–2004 GMC Sierra HD: Allison NSBU (neutral start backup) switch failure - blank/flashing PRNDL — test first, then buy for this job.
The price range below is a national planning range for P0708 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $200
Labor$100 – $300
Transmission range sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0708 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The sensor is on the transmission; alignment matters.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →