P0504

P0504 on a 2010–2019 Subaru Outback: Brake switch A/B correlation

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0504 on a 2006–2011 BMW 3 Series · 2012–2018 BMW 3 Series · 2010–2017 Chevrolet Equinox · 2011–2019 Ford Explorer · 2014–2018 GMC Sierra 1500 · 2011–2019 Hyundai Sonata
Show all 11 vehicles with this code

2011–2021 Jeep Grand Cherokee · 2007–2018 Jeep Wrangler · 2013–2018 Nissan Altima · 2010–2019 Subaru Outback · 2005–2023 Toyota Tacoma

DIY difficulty 1/5

Your brake light switch is sending conflicting signals. Your brake lights might not work - which is a safety issue - and cruise control may quit.

Model notes: Check brake light operation first - if the brake lights don't work, other drivers can't see you stopping.

Key facts

☑ Before you buy parts — check these first:
On your 2010–2019 Subaru Outback (2.5L EJ25, 2.5L FB25) — Front brake pads and rotors: Owner-verified
Lift, remove the wheel. Remove the two caliper slide-pin bolts (14mm heads) and pivot the caliper up or hang it from the strut — never let it hang by the brake hose. For rotors, remove the caliper bracket (17mm bolts) to free the disc. Rusted rotors are common; the rotor has two threaded jack holes — screw in M8 bolts evenly to press a stuck rotor off the hub instead of hammering it. Pull the slide pins, clean them of rust with penetrant/steel wool, and re-lube with silicone-based grease; apply brake grease/PBC grease to pad ears and clips, not the friction surfaces. Compress the piston with a C-clamp or old pad (loosen the master-cylinder cap and watch the fluid level), fit new pads and hardware, reinstall bracket and caliper, torque, then pump the brake pedal to seat the pads before driving.
Do this test first: Check brake light operation
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0504 on the 2010–2019 Subaru Outback — but the community-sourced Front brake pads and rotors note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: 2010 Subaru Legacy/Outback FSM — Front Brake Pad (caliper bolt 27 N·m) · LegacyGT — Brake Pad Replacement Walkthrough (bracket bolts, M8 rotor holes, slide pins) · LegacyGT — 2013 Subaru Legacy Torque Specs (lug nuts ~89 ft-lb, caliper bolts ~20 ft-lb)

Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0504: 11 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 2 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check brake light operation Tests: Failed brake light switch (very common, cheap part)
  2. Watch both switch circuits in scan tool while pressing the pedal

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2010–2019 Subaru Outback: Front brake pads and rotors — test first, then buy for this job.

Expensive fork: Brake caliper — if a wheel drags or overheats after fresh pads and rotors. The price range below is a national planning range for P0504 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$15 – $40
Labor$50 – $120

The switch is cheap and usually a simple swap. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0504 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

1 of 5 — A cheap part and a simple swap.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →