2010–2019 Subaru Outback

Community-sourced DIY repair guides for the 2010–2019 Subaru Outback, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.

Owner-verified repair guides

Front brake pads and rotors Owner-verified (2.5L EJ25, 2.5L FB25)

Lift, remove the wheel. Remove the two caliper slide-pin bolts (14mm heads) and pivot the caliper up or hang it from the strut — never let it hang by the brake hose. For rotors, remove the caliper bracket (17mm bolts) to free the disc. Rusted rotors are common; the rotor has two threaded jack holes — screw in M8 bolts evenly to press a stuck rotor off the hub instead of hammering it. Pull the slide pins, clean them of rust with penetrant/steel wool, and re-lube with silicone-based grease; apply brake grease/PBC grease to pad ears and clips, not the friction surfaces. Compress the piston with a C-clamp or old pad (loosen the master-cylinder cap and watch the fluid level), fit new pads and hardware, reinstall bracket and caliper, torque, then pump the brake pedal to seat the pads before driving.

Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: 2010 Subaru Legacy/Outback FSM — Front Brake Pad (caliper bolt 27 N·m) · LegacyGT — Brake Pad Replacement Walkthrough (bracket bolts, M8 rotor holes, slide pins) · LegacyGT — 2013 Subaru Legacy Torque Specs (lug nuts ~89 ft-lb, caliper bolts ~20 ft-lb)

C0035 on this Subaru Outback — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Battery replacement Owner-verified (2.5L EJ25, 2.5L FB25)

The 12V battery (Group 25; ~356 CCA OEM) sits in the front of the engine bay on the driver side, secured by a hold-down bracket. Tools: 10mm socket/ratchet, terminal brush, gloves. Disconnect the NEGATIVE cable first, then the positive (keeps a wrench slip from shorting to ground). Remove the hold-down bracket bolts, lift the old battery straight up by its handle or from the bottom, and clean the tray and terminal clamps with a brush. Set the new battery in, reinstall and snug the hold-down bracket, then connect POSITIVE first, then negative, and snug the clamps. Use a 9V memory saver if you want to keep presets.

Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).

Typical time: “Subaru idle relearn: turn off lights, A/C, stereo; reconnect battery; key to ON for 10–15 seconds without starting so the throttle body finds its home position; start and idle 10 minutes with no load, never touching the…” — as written in the note. First-timers often take twice this.

Torque specs

Tips

Sources: JustAnswer — 2015 Outback battery replacement steps (Group 25, 10mm, bracket, terminal order) · UltimateSubaru — 2015 Outback Battery Issues (dealer: 15–20 min idle relearn; Group 25 356 CCA) · UltimateSubaru — Subaru Idle Relearn Procedure (step-by-step) · YouTube — WildCatDIY: Battery replacement 2015-2019 Subaru Outback

P0562 on this Subaru Outback — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

Codes on this Outback

C0035
2010–2019 Subaru Outback
Front brake pads and rotors
C0040
2010–2019 Subaru Outback
Front brake pads and rotors
C0045
2010–2019 Subaru Outback
Front brake pads and rotors
C0050
2010–2019 Subaru Outback
Front brake pads and rotors
P0504
2010–2019 Subaru Outback
Front brake pads and rotors
P0562
2010–2019 Subaru Outback
Battery replacement
P0563
2010–2019 Subaru Outback
Battery replacement

What owners report

NHTSA recorded 934 complaints for the 2010–2019 Subaru Outback. 2016 was the worst year (642 complaints). Most-reported areas: electrical system, power train, unknown or other.

Counts are NHTSA complaints filed for these model years, via the NHTSA API. See data for all Outback years →

Recalls

20 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.

Factory service bulletins

NHTSA has published 1,422 manufacturer communications (service bulletins, dealer notices) covering the 2010–2019 Subaru Outback.

Most cited systems: Equipment (616), Electrical System (507), Power Train (118), Engine (118), Engine And Engine Cooling (99).

Latest bulletins:

NHTSA also opened 2 defect investigations covering these years.

Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.

Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.