Diagnose soonIf your brake lights aren't working, fix this immediately - other drivers can't see you braking.
Your brake light switch is sending conflicting signals. Your brake lights might not work - which is a safety issue - and cruise control may quit.
Model notes: Check brake light operation first - if the brake lights don't work, other drivers can't see you stopping.
Key facts
P0504 means brake switch A/B correlation. Your brake light switch is sending conflicting signals. Your brake lights might not work - which is a safety issue - and cruise control may quit. WrenchFair's published fair-price range for this repair is $15–$40 parts and $50–$120 labor at independent shops.
WrenchFair rates P0504 a 1-of-5 DIY difficulty (“A cheap part and a simple swap.”) with a “Diagnose soon” driveability rating: If your brake lights aren't working, fix this immediately - other drivers can't see you braking. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 1,210 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Power Train) — see the latest ones
On your 2007–2018 Jeep Wrangler (3.6L Pentastar V6) — Front brake pads and rotors:Owner-verified
Raise the front, remove the wheel. Unbolt the caliper from the back and pull it off the bracket — hang it with wire, never from the brake hose. Compress the piston with a C-clamp before fitting thicker pads. For rotors, remove the two large caliper-bracket-to-knuckle bolts (21mm head) and pull the rotor straight off the hub. JK-specific quirk: JK rotors have NO retaining screws (that's a JL thing). Factory JK rotors are held by push-on retaining CLIPS on the wheel studs — cut/pry them off and discard them; they are one-time assembly aids. Expect rust between rotor and hub; a few taps with a rubber mallet on the rotor hat breaks it free. Slide pins pull out of the bracket for cleaning and re-greasing.
Do this test first: Check brake light operation
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0504 on the 2007–2018 Jeep Wrangler — but the community-sourced Front brake pads and rotors note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Front caliper bracket-to-knuckle bolts (21mm): 120 ft-lbs — Matches the JK factory torque sheet (163 N.m); confirmed on a JK front brake install.
Caliper slide-pin (caliper-to-bracket) bolts: 26 ft-lbs — Factory caliper mounting bolt value (35 N.m) reused on JK installs; clean pins and re-grease.
Lug nuts: 100 ft-lbs — JK wheel torque confirmed in multiple JK guides.
Rear caliper bracket bolts (for reference): 75 ft-lbs — Rear-only; fronts are 120 ft-lbs. Don't mix them up.
Tips
Factory threads use threadlocker; clean the bracket bolts with brake cleaner and apply fresh threadlocker on reinstall (DIYers commonly use red on the bracket bolts).
Clean old grease off the slide pins, inspect the rubber boots, and re-grease lightly — seized pins are the usual cause of uneven JK pad wear.
The JK has a solid rear rotor and vented front rotor; confirm left/right rotor orientation before mounting.
Minimum pad thickness is 2-3mm per the JK brakes diagnostic guide; squealing means the wear indicators are already talking.
Pump the brake pedal to seat the pads before driving, then bed the pads with several moderate stops.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
brake lights stuck on or not working
cruise control inoperative
EPC light
cannot shift from park
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed brake light switch (very common, cheap part) 11 owner notes link this repair to P0504
Misadjusted switch
Wiring fault
Owner notes linked to P0504: 11 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Watch both switch circuits in scan tool while pressing the pedal
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2018 Jeep Wrangler: Front brake pads and rotors — test first, then buy for this job.
Expensive fork: Brake caliper — if a wheel drags or overheats after fresh pads and rotors.
The price range below is a national planning range for P0504 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$15 – $40
Labor$50 – $120
The switch is cheap and usually a simple swap. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0504 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →