Diagnose soonDrivable but often down on power; a wrong reading can prevent DPF regeneration.
Your diesel has a sensor watching exhaust back-pressure for the turbo and emissions systems, and its signal is wrong. The number-one cause is the little sampling tube to the sensor getting clogged with soot - check that first, because a new sensor on a blocked tube will read wrong too.
Key facts
P0471 means exhaust Pressure Sensor Range/Performance. Your diesel has a sensor watching exhaust back-pressure for the turbo and emissions systems, and its signal is wrong. The number-one cause is the little sampling tube to the sensor getting clogged with soot - check that first, because a new sensor on a blocked tube will read wrong too. WrenchFair's published fair-price range for this repair is $60–$200 parts and $100–$250 labor at independent shops.
WrenchFair rates P0471 a 2-of-5 DIY difficulty (“Tube inspection and cleaning is easy; the sensor is usually accessible.”) with a “Diagnose soon” driveability rating: Drivable but often down on power; a wrong reading can prevent DPF regeneration. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2007–2018 Ram 3500 (6.7L Cummins I6 (ISB)) — MAP sensor + exhaust back-pressure tube soot cleaning — P0471/P0472:Owner-verified
Easy driveway maintenance — T15 Torx and a can of electronics/MAF cleaner for the MAP sensor; basic hand tools, solvent, and compressed air for the EBP tube.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0471 on the 2007–2018 Ram 3500 — but the community-sourced MAP sensor + exhaust back-pressure tube soot cleaning — P0471/P0472 note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Tips
On a stock 6.7 with a working EGR system, the MAP sensor sits in the intake horn right where exhaust gas re-enters — it cakes with soot until it reads wrong. Symptoms creep up: slow throttle response, worse fuel economy, more frequent DPF regens, and eventually codes. Owners report roughly 3 MPG coming back after a cleaning.
It is a 10-minute maintenance item, not a parts replacement: one T15 Torx, pull the sensor, spray with electronics or MAF cleaner — not brake cleaner, which can attack the sensor — let it soak if it is badly caked, reinstall. Make it part of every oil change or every other, depending on how you drive.
The exhaust back-pressure sensor's tube (off the exhaust manifold, above the turbo) plugs with soot the same way and sets P0471/P0472/P0473 range/performance codes. Pull the tube, clean it with solvent and a pipe cleaner plus compressed air, and inspect it for leaks or damage before you buy a sensor — the tube is the cause more often than the sensor itself.
If cleaning does not fix it, the sensor is roughly $45 and a simple swap; check the connector and wiring first. Diagnostic cross-check: at key-on/engine-off, the exhaust-pressure reading should agree with MAP and barometric pressure — a sensor reading out of line with the other two is the bad one.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light on
reduced engine power
poor turbo response
DPF warning on diesels
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
soot-clogged sensor sampling tube
failed exhaust pressure sensor
wiring damaged by exhaust heat
corroded or loose connector
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Remove the sensor's sampling tube and check for carbon blockage - clean it out. Tests: soot-clogged sensor sampling tube
Watch the pressure reading with live data; compare against expected values at idle and under load. Tests: failed exhaust pressure sensor
Check the wiring for heat damage. Tests: wiring damaged by exhaust heat
With the key on and engine off, check the reference voltage and ground at the component connector with a multimeter.
Replace the sensor only if the tube is clear and the reading is still wrong.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2018 Ram 3500: MAP sensor + exhaust back-pressure tube soot cleaning — P0471/P0472 — test first, then buy for this job.
The price range below is a national planning range for P0471 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$60 – $200
Labor$100 – $250
Exhaust pressure sensor or sampling tube cleaning. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0471 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Tube inspection and cleaning is easy; the sensor is usually accessible.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →