P0471

P0471 on a 2007–2018 Ram 3500: Exhaust Pressure Sensor Range/Performance

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0471 on a 2007–2018 Ram 3500

DIY difficulty 2/5

Your diesel has a sensor watching exhaust back-pressure for the turbo and emissions systems, and its signal is wrong. The number-one cause is the little sampling tube to the sensor getting clogged with soot - check that first, because a new sensor on a blocked tube will read wrong too.

Key facts

☑ Before you buy parts — check these first:
On your 2007–2018 Ram 3500 (6.7L Cummins I6 (ISB)) — MAP sensor + exhaust back-pressure tube soot cleaning — P0471/P0472: Owner-verified
Easy driveway maintenance — T15 Torx and a can of electronics/MAF cleaner for the MAP sensor; basic hand tools, solvent, and compressed air for the EBP tube.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0471 on the 2007–2018 Ram 3500 — but the community-sourced MAP sensor + exhaust back-pressure tube soot cleaning — P0471/P0472 note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Tips

Sources: 6.7L Cummins exhaust gas pressure sensor tube — clean and inspect for reuse (service procedure) · 6.7L Cummins exhaust gas pressure sensor tube — removal procedure (service procedure) · How to locate and clean exhaust back pressure sensor and tube, 6.7 Cummins (repair video)

Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
  2. Remove the sensor's sampling tube and check for carbon blockage - clean it out. Tests: soot-clogged sensor sampling tube
  3. Watch the pressure reading with live data; compare against expected values at idle and under load. Tests: failed exhaust pressure sensor
  4. Check the wiring for heat damage. Tests: wiring damaged by exhaust heat
  5. With the key on and engine off, check the reference voltage and ground at the component connector with a multimeter.
  6. Replace the sensor only if the tube is clear and the reading is still wrong.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2007–2018 Ram 3500: MAP sensor + exhaust back-pressure tube soot cleaning — P0471/P0472 — test first, then buy for this job.
The price range below is a national planning range for P0471 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$60 – $200
Labor$100 – $250

Exhaust pressure sensor or sampling tube cleaning. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0471 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Tube inspection and cleaning is easy; the sensor is usually accessible.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: Sensor mounting bolts: typically 8–12 Nm — verify spec. Never overtighten sensors with plastic bodies.

Pro tip: Check wiring and connectors first — chafed wires and corroded pins cause more sensor codes than dead sensors do.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →