Diagnose soonA bad sensor reading can cause poor running or stalling. Drive carefully and diagnose soon.
Your gas gauge is lying - it reads full (or pegged past full) no matter how much gas is in the tank. The sensor in the tank has an electrical fault.
Model notes: Fuel senders wear where the wiper sits most - the gauge often works at some levels and lies at others before failing completely. Note which fuel levels read wrong; it confirms the diagnosis.
Key facts
P0463 means fuel level sensor A circuit high input. Your gas gauge is lying - it reads full (or pegged past full) no matter how much gas is in the tank. The sensor in the tank has an electrical fault. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$200 labor at independent shops.
WrenchFair rates P0463 a 3-of-5 DIY difficulty (“The sender is part of the fuel pump module inside the tank - access is the work.”) with a “Diagnose soon” driveability rating: A bad sensor reading can cause poor running or stalling. Drive carefully and diagnose soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 1,575 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Structure) — see the latest ones
On your 2019–2026 Ram 1500 (5.7L HEMI V8) — Fuel pump replacement:Owner-verified
The DT bed has no factory fuel pump access panel (confirmed by a 2019 DT 5.7 owner), so the in-tank module is reached either by lifting or sliding the bed (six bed bolts, plus disconnecting taillight wiring and the filler neck screws) or by lowering the tank on a jack. Owners report the bed method is easier with a full tank, while dropping the tank on rust-belt trucks risks snapping strap bolts. A solo-owner trick: remove only the driver-side bed bolts, loosen the passenger side a few turns, jack that side up and brace it instead of fully removing the bed.
Do this test first: Compare the fuel level PID to the gauge - both wrong together points at the sender
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0463 on the 2019–2026 Ram 1500 — but the community-sourced Fuel pump replacement note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Fuel pump lock ring: verify — Confirm against factory service info for the 5.7L HEMI before installing. Do not hammer it on at max force; seat it to the 'lock' position.
Bed bolts: verify — Confirm against factory service info for the 2019+ Ram 1500 DT before torquing.
Tips
Soak the lock ring and fuel-line fittings in PB Blaster for a few days before the job if you live in a rust/salt region; rusted rings often need a new ring ordered along with the pump.
Crack the lock ring loose with a rented OEM fuel pump retainer-ring remover (AutoZone/O'Reilly loaner program) instead of hammering if the ring is corroded — mangling the ring's mating surface ruins the tank.
The fuel line needs a quick-disconnect tool (some owners cut one down to ~1/4 inch to fit behind the connector) plus a tug-check that fuel and electrical connectors are locked before reinstalling.
The module's seal/gasket goes on top of the pump body with the fuel line port facing the driver side; new gaskets that are too thick can prevent the ring from seating — reuse the old one only if it is still in good shape.
After install, turn the key to ON three times (listening for the pump prime each time) before cranking to start.
One dealer quote for a failed 2019 DT 5.7 pump was $1,470, and the pump is NOT covered by the powertrain warranty — a DIY is the budget move.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
fuel gauge stuck on full or erratic
distance-to-empty reading wrong
EVAP tests not running
check engine light
false low-fuel warning light or chime
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed fuel level sender (most common - worn resistive wiper) 11 owner notes link this repair to P0463
Signal wire shorted to voltage
Corroded connector at the tank
Stuck float arm
Owner notes linked to P0463: 11 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Compare the fuel level PID to the gauge - both wrong together points at the sender Tests: Failed fuel level sender (most common - worn resistive wiper)
Check the connector at the tank for corrosion Tests: Corroded connector at the tank
Test sender resistance through its sweep if accessible
Replace the sender (often serviced with the pump module) if it tests bad
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2019–2026 Ram 1500: Fuel pump replacement — test first, then buy for this job.
The price range below is a national planning range for P0463 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $120
Labor$80 – $200
Sensor replacement is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0463 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The sender is part of the fuel pump module inside the tank - access is the work.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →