Community-sourced DIY repair guides for the 2019–2026 Ram 1500, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
The 5.7L HEMI runs 16 spark plugs — two per cylinder — so buy 16 (the 3.6L V6 has one per cylinder). Pop the engine cover, then unbolt each of the 8 coil packs with a 10mm socket. Reach the rear cylinders by laying across the engine on a blanket or layover creeper; the driver's-side rear plugs sit under the brake booster, and the #8 plug is crowded by the PCM wiring harness plus two heater-core hoses. Blow out each plug well before removal and do one cylinder at a time so no debris enters the combustion chamber.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Torque specs
Spark plugs: 13 ft-lbs (156 in-lbs); do not exceed 15 ft-lbs — Per service manual as cited by forum members; torque-critical tapered design.
Ignition coil bolts: verify — Confirm against factory service info for this engine before torquing.
Tips
The 5th-gen 5.7 uses factory iridium plugs on a 100k-mile interval per the owner's manual — don't change them at 30k assuming the old copper-plug schedule.
Verify the 0.043 in (1.1 mm) gap even on pre-gapped plugs, and use only a light smear of anti-seize; the plugs use crush washers that seat as you torque.
Rotate each new plug counterclockwise until it clicks into the threads before tightening to avoid cross-threading the aluminum heads; torque to 13 ft-lbs and never exceed 15 ft-lbs per the service-manual warning.
Coils lift off easily thanks to factory dielectric grease — dab fresh dielectric grease inside the boots on reassembly so they don't seize to the plugs over time.
The 5.7 HEMI has four O2 sensors: one cat per bank, with an upstream and downstream sensor on each — bank 1 is the driver's side, bank 2 the passenger side, sensor 1 before the cat, sensor 2 after. Reach them from under the truck; bank 2 sensor 1 sits in the passenger-side exhaust ahead of the catalytic converter. On the 2019 5.7L non-eTorque, owners report the upstream sensors carry a different part number than the downstream ones, so order by exact position rather than buying four of the same sensor.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
Torque specs
O2 sensor: verify — Confirm against factory service info for this engine before torquing.
Tips
Order by position: on the 2019 5.7L non-eTorque the upper (upstream) O2 sensors are a different part number from the lower bank (downstream) sensors.
If a heater-circuit code won't clear after replacing the flagged sensor, owners report having to replace both sensors on that same bank for the ECU to accept the reset.
Check for exhaust leaks and damaged wiring (shorted or frayed harness, tangled connector slack) before condemning the sensor — forum P0153/P0155 troubleshooting starts there.
Seized threads are common on high-mileage trucks; use a dedicated O2 sensor socket or long 7/8-in wrench plus penetrating oil, and disconnect/unclip the connector before removal.
The thermostat sits in a two-bolt aluminum housing at the front of the 5.7L HEMI where the radiator hose meets the water-pump inlet — a 2019 (DT-gen) owner describes it as simply clamping the hose near the thermostat, pulling two bolts, and swapping the stat. Drain the coolant below housing level first (or clamp the hose and work quickly), pull the hose off with spring-clamp pliers, remove the two housing bolts, and swap the thermostat with its rubber O-ring seated in the stepped lip. The aluminum housing strips easily, so use a 1/4-in drive or inch-pound wrench.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
Thermostat housing bolts: 112 in-lbs — Per the service manual as cited by forum members; the aluminum housing strips easily, so do not over-tighten.
Tips
Bleeding is the real job on a HEMI: plan several fill/heat-cycle bleeds — owners report temp spikes and overheating after a stat swap whenever air stays trapped in the system.
For a quick swap without a full drain, clamp the hose, crack the housing corner loose over a ziplock bag to catch coolant, swap the stat, then top up the overflow.
If the housing is corroded or out-of-round it will weep coolant every winter; the housing is cheap, so replace it while you're in there and consider a screw clamp over the tired spring clamp.
Stick with the OE temperature rating (203–209°F range) unless you're tuned for a cooler stat — a stat that runs the engine too cold can set P0128 for coolant below thermostat regulating temperature.
Front brake pads & rotors Owner-verified(5.7L HEMI V8)
Caliper bracket bolts are factory-coated in threadlocker and extremely tight to break free — owners report needing a breaker bar (described as 'a combination of loctite and torque' on the 2019 DT). Remove the wheel, unbolt the caliper from the bracket, unbolt the bracket from the knuckle, and the rotor slides off the hub. If swapping calipers, plug both sides of the banjo bolt with banjo shutter pliers to limit brake fluid leakage during the swap.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Caliper bracket (mount) bolts: 130 ft-lbs — Confirmed by multiple RamForum owners for the 2019+ light-duty front brakes; 2019-2025 walkthrough video also lists 130 ft-lbs.
Caliper slide pin bolts: verify — Conflicting values across sources (31 ft-lbs per 2019-2025 walkthrough video vs 26 ft-lbs per RamForum service-info pull). Confirm against factory service info for this engine.
Brake hose banjo bolt: 30 ft-lbs — Per 2019-2025 front brake caliper walkthrough torque list.
Lug nuts: 130 ft-lbs — Per 2019-2025 front brake caliper walkthrough torque list.
Tips
Expect the factory threadlocker on the bracket bolts to fight you — use a long breaker bar, not just a ratchet.
The 2019-2025 walkthrough specifies 15/16/17/21 mm sockets for the job; verify fit on your truck before starting.
If the caliper is being replaced, cap the banjo bolt opening on both sides to keep fluid loss minimal and bleed afterward.
Battery is under the hood in the engine bay, retained in its tray by hold-down clamps. The main clamp is a single bolt on the engine side of the tray (limits driver-to-passenger movement). A second clamp on the firewall side limits front-to-back movement — owners report this firewall-side clamp is hard to reach and the dealer claims it needs a 'special' tool. The Intelligent Battery Sensor (IBS) is clamped to the negative battery post; keep it seated and tight, since the BCM uses it for charge/load management. The stock battery is Group H7; the tray is sized for an H8 — owners upgrade to H8 AGM by popping out the removable plastic spacer in the tray, after which the H8 fits and the hold-down re-bolts.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Typical time: “If you want the IBS to re-learn, one owner relayed RAM tech-line advice: leave the negative cable disconnected at least 2 hours when swapping; FCA's STAR Center documentation describes IBS SOC adaptation as needing 1…” — as written in the note. First-timers often take twice this.
Torque specs
Battery hold-down clamp bolt: verify — Confirm against factory service info for this engine.
Tips
No dealer 'registration' of the new battery is required on RAM (unlike BMW/Ford) — owners report it is a basic swap.
Multiple owners report that a worn battery shows voltage near 12V with the engine off while the IBS cuts non-essential loads (heated seats etc.) to protect cranking power.
If you want the IBS to re-learn, one owner relayed RAM tech-line advice: leave the negative cable disconnected at least 2 hours when swapping; FCA's STAR Center documentation describes IBS SOC adaptation as needing 1 crank plus 2-4 hours of quiescent (sleep) time.
For eTorque trucks, there is ALSO a 48V battery pack behind the rear seat (driver side) — that is separate from this 12V underhood battery replacement.
Consider a battery-memory saver on the OBD port so modules don't need several drive cycles to resync; one 2019 owner reported 3 drive cycles before cruise control returned.
The DT bed has no factory fuel pump access panel (confirmed by a 2019 DT 5.7 owner), so the in-tank module is reached either by lifting or sliding the bed (six bed bolts, plus disconnecting taillight wiring and the filler neck screws) or by lowering the tank on a jack. Owners report the bed method is easier with a full tank, while dropping the tank on rust-belt trucks risks snapping strap bolts. A solo-owner trick: remove only the driver-side bed bolts, loosen the passenger side a few turns, jack that side up and brace it instead of fully removing the bed.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Torque specs
Fuel pump lock ring: verify — Confirm against factory service info for the 5.7L HEMI before installing. Do not hammer it on at max force; seat it to the 'lock' position.
Bed bolts: verify — Confirm against factory service info for the 2019+ Ram 1500 DT before torquing.
Tips
Soak the lock ring and fuel-line fittings in PB Blaster for a few days before the job if you live in a rust/salt region; rusted rings often need a new ring ordered along with the pump.
Crack the lock ring loose with a rented OEM fuel pump retainer-ring remover (AutoZone/O'Reilly loaner program) instead of hammering if the ring is corroded — mangling the ring's mating surface ruins the tank.
The fuel line needs a quick-disconnect tool (some owners cut one down to ~1/4 inch to fit behind the connector) plus a tug-check that fuel and electrical connectors are locked before reinstalling.
The module's seal/gasket goes on top of the pump body with the fuel line port facing the driver side; new gaskets that are too thick can prevent the ring from seating — reuse the old one only if it is still in good shape.
After install, turn the key to ON three times (listening for the pump prime each time) before cranking to start.
One dealer quote for a failed 2019 DT 5.7 pump was $1,470, and the pump is NOT covered by the powertrain warranty — a DIY is the budget move.
Throttle body cleaning Owner-verified(5.7L HEMI V8)
The DT 5.7L HEMI uses a fully electronic throttle body held to the intake manifold by 4 bolts plus an electrical connector; pull the air intake tube off first for access. For cleaning, the factory service info forbids spray (carb) cleaners and silicone lubricants — wipe the bore and plate with brake cleaner applied to a cloth, never sprayed directly into the throttle body. Critically, do not force the throttle plate open while cleaning: owners report that throws the PCM calibration off and causes surging or very high idle.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Torque specs
Throttle body mounting bolts (4): verify — Confirm against factory service info for the 5.7L HEMI before torquing.
Tips
5.7L V-8 throttle body reset procedure (from factory service info) after removal/cleaning/replacement: disconnect negative battery cable ~90 seconds, reconnect, turn key ON but DO NOT crank, leave ON at least 10 seconds so the PCM learns throttle body parameters, turn key OFF, then crank and start normally.
On replacement some owners also do the 'pedal to the floor' relearn: after reconnecting the battery, key ON, wait for dash lights to go out, then slowly depress and release the accelerator.
If the red lightning-bolt (ETC) warning appears after cleaning, disconnect and clean the throttle body electrical connector and pins with electrical contact cleaner and add dielectric grease before condemning the throttle body.
If cleaning doesn't fix a red lightning-bolt/limp condition, the throttle body (or the accelerator pedal position sensor, which talks to the PCM that drives the throttle body) is the likely next suspect — watch pedal-position data for glitches on a scan tool.
Never polish or port the throttle plate area; owners have destroyed sensitive throttle bodies attempting it, with P2110 forced-limited-RPM faults after.
Transmission fluid & filter service Owner-verified(5.7L HEMI V8)
The DT 5.7L uses the ZF 8HP75 with no dipstick; ZF markets it 'lifetime fill' but it is fully owner-serviceable — the filter is built into the plastic transmission pan, so service means replacing the whole pan/filter assembly (13 T40 Torx bolts). The fill plug (8mm hex) sits on the passenger side at the rear of the transmission above the exhaust and must be cracked loose BEFORE draining — the drain plug (10mm hex) is at the rear of the pan, and some newer pans omit the drain plug entirely (then fluid drains over the pan edge during removal). The critical Ram-only quirk: the transmission sits tilted in the chassis, so the pan rail — not the truck — must be level, requiring the rear tires to be raised roughly 8-9 inches; verify with a bubble level on the pan rail.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Transmission pan bolts (13, T40): 8-10 Nm — First pass 5 Nm in crisscross pattern, then final 8-10 Nm crisscross. Never exceed 10 Nm and never use air/electric tools — overtightening shears bolt heads and crushes the gasket. From Blauparts factory-procedure writeup.
Transmission drain plug: 8 Nm — Do not overtighten. From Blauparts factory-procedure writeup.
Transmission mount nuts (3, on cross member): 30 ft-lb — 16mm socket. Only loosened if elevating the rear of the transmission ~1 inch for deep-pan clearance on removal. From Blauparts factory-procedure writeup.
ATF capacity, pan + filter service: 5.8 qt (5.5-6.0 L) — Dry fill 8.7 qt. Buy at least 6-7 liters. Expect ~4.5-5.5 qt back in after a drain; level is set by the overflow method, not a dipstick. From Blauparts guide.
Tips
Fluid spec is Mopar 68218925AA — Mopar 8 & 9 Speed ATF, which is ZF Lifeguard 8 in a Mopar bottle; do not substitute generic ATF.
Fill from below with a hand fluid pump until fluid overflows the fill hole, thread the plug in halfway, then start the engine, cycle through the gears (get it to shift to 2nd), and with the engine RUNNING top off until a steady stream runs out — then install the fill plug.
The final level must be set with transmission fluid temperature between 86-122 F (30-50 C); start the service with a COLD transmission (below 86 F) or you will run out of temperature window. Monitor temp on the cluster's vehicle info screen or a scan tool.
Recommended service interval is every 60,000 miles (40-50k under severe/towing use); the pan comes with a new gasket, filter seal to the valve body, and magnets — lubricate the filter-to-valve-body O-ring with fresh ATF on install and never use RTV on the pan.
Working under a running truck is unavoidable for the level-setting step — wear heat-protective gloves near the exhaust and never fully torque the drain plug by feel alone.
8HP75 drain-and-fill service (DT) Owner-verified(5.7L HEMI V8, 3.6L Pentastar V6)
All under the truck on stands or a lift. Break the 8mm-hex fill plug loose FIRST (passenger side, right rear of the transmission, above the exhaust) before touching the drain plug - if you can't refill it, don't drain it.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Pan drain plug: 5-6 ft-lb (owner-reported; verify) — Owner-reported ~5-6 ft-lb; barely more than snug. Verify against service info.
Tips
Ignore the 'lifetime fill' line in the owner's manual: ZF (the transmission maker) recommends fluid and filter service at roughly 50,000 miles / 8 years. Owners who tow service earlier, at 30,000 miles - and report smoother shifts after, especially between the top gears.
Use the right fluid and don't mix cheaply: Mopar 8/9-speed or ZF Lifeguard 8 (it has a green tint). A 5thGenRams owner warns a pan-drop leaves a lot of old fluid behind, so mixing in an incompatible fluid is the fastest way to a $5,000-6,000 transmission replacement. Some owners report good results with Liqui Moly ATF 1800, but the Mopar/ZF fluid is the safe consensus.
The Ram-specific gotcha: the transmission sits pointing downhill, so the pan rail is NOT level with the truck on flat stands. Factory ZF instructions want the transmission level - owners raise the rear tires ~8-9 inches to get the pan rail level before the final fill check.
Mind the drain plug clearance: the 10mm pan drain plug nearly touches the exhaust crossover, and a hex socket plus ratchet won't fit. Owners improvise - one used an Allen key in the socket's lock-pin hole as a lever, another cut a cheap 10mm hex socket down so a wrench fits. Jacking the back of the transmission up adds clearance.
Final fill must be done with the engine RUNNING and the fluid between 86-122F, cycling through the gears (Reverse, Neutral, Drive, hold brake 5 sec each). One owner pulled the fill plug at temp, saw fluid flowing, started the truck, and still added another quart - 5.5-6 quarts total on his drain-and-fill.
The filter is built into the plastic pan, so a filter change means a new pan. Owners either buy the Dorman pan with a replaceable filter layer (next service is just the filter) or cross-reference the ZF pan from BMW applications - but measure the old pan, since Ram pans are deeper on some builds.
Open the tailgate and eyeball the strikers on both bed sides against the latches - misalignment is visible. The recall remedy is a free dealer inspection/adjustment, so the DIY win is knowing you qualify.
Tips
This is a real, huge recall: NHTSA campaign 22V-904 (FCA number ZB8) covers 2019-2022 Ram 1500/2500/3500 - over 1.2 million trucks in the US alone. Misaligned tailgate strikers can let the tailgate unlatch and drop while driving, spilling cargo into traffic. Stellantis logged 800+ warranty claims before acting.
The fix is free and simple: dealers inspect the tailgate striker alignment to the box latch and adjust if needed, at no charge. If your tailgate ever drops on its own or feels loose when closed, don't assume it's wear - check for this recall first.
Check your VIN on NHTSA's recall site before spending a dollar. A tailgate that 'just needs a new latch' is a dealer visit, not a parts order - and the adjustment is on FCA's tab.
Only about 1% of the recalled trucks are believed to actually have misaligned strikers, so this is a check-and-adjust recall, not a parts-swap - most owners are in and out of the dealer with no parts changed.
All under the hood at the front of the engine - no lift needed. The eTorque trucks have TWO tensioners (one high, one low on the motor), and the belt tensioner stop bracket must come off to get the new belt on.
Typical time: “This is a belt job, not a hybrid-system job: owners report the aftermarket belt costs ~$40 and installs in an hour or less, while one dealer quoted $1,800 for the same work.” — as written in the note. First-timers often take twice this.
Torque specs
Belt tensioner / idler fasteners: verify — No published owner torque figure for the eTorque belt path - torque to service-info spec; the tensioner stop bracket must be removed and reinstalled to seat the belt.
Tips
Know the failure: the wide eTorque belt shreds from the back (engine) side, sometimes every 7,000-9,000 miles on unlucky trucks. Owners report it 'coming apart' as low as 10,000 miles. Chirping from the belt area on a 5.7 eTorque is the early warning - check the belt edges for separation.
This is a belt job, not a hybrid-system job: owners report the aftermarket belt costs ~$40 and installs in an hour or less, while one dealer quoted $1,800 for the same work. You don't touch the MGU or the 48V battery for a belt swap - that's the line between this DIY note and the dealer-only MGU repair (parts need computer marry/match).
The install trick: eTorque trucks have two tensioners, and getting the new belt seated is genuinely fiddly. One owner couldn't get the new belt on until he removed the belt tensioner stop bracket - with it off, the belt went on fine. Photograph the routing before the old belt comes off.
Buy the RIGHT width: owners found 2019-2021 trucks with a narrower ~13/16-inch belt and later trucks with a 1-1/8-inch wide belt. Match your old belt's width and rib count - parts stores' catalogs get this wrong, so bring the old belt to compare.
Replace the little water-pump stretch belt while you're in there - owners on the same thread report those failing too, and it's cheap insurance once the main belt is off.
Repeat shredding points past the belt: one owner had the belt fail 4 times before the dealer replaced the eTorque unit itself (updated part number) under engineering direction. If a fresh belt shreds again within ~10,000 miles, suspect a misaligned pulley or binding MGU - that part IS a dealer repair.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
DIY-friendliness scorecard
Score: 78/100 — DIY with care
Special tools mentioned in the notes (3, −12): O2 sensor socket, scan tool with live data, Torx bits.
Documented dealer-only steps (1, −15): • You don't touch the MGU or the 48V battery for a belt swap - that's the line between this DIY note and the dealer-only MGU repair (parts need computer marry/match) (eTorque drive belt shredding/failure (DIY))
How this is scored (mechanical, no opinion): start at 100; −4 per distinct special tool mentioned in the notes (max −28); −15 per documented dealer-only step (max −30); note-volume band: 15+ notes +10, 8–14 +5, 4–7 +0. Bands: 85+ DIY-friendly · 65–84 DIY with care · 40–64 Experienced DIY only · below 40 Think twice. Pilot rubric — flagged for Robbie’s eyeball before any scale-up.
NHTSA recorded 631 complaints for the 2019–2026 Ram 1500. 2020 was the worst year (631 complaints). Most-reported areas: electrical system, engine, unknown or other.
19V407000 (31/05/2019) — AIR BAGS Chrysler (FCA US LLC) is recalling certain 2019-2020 Ram 1500 vehicles. The flash memory of the Occupant Restraint Controller (ORC) may become corrupted, disabling the vehicle's air bags and seat belt pretensioners.
26V495000 (30/07/2026) — SEAT BELTS:REAR/OTHER:ANCHORAGE Chrysler (FCA US, LLC) is recalling certain 2019-2026 Ram 1500 vehicles. The second-row center and left-side seat belt buckle anchors may have been improperly installed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety…
20V513000 (27/08/2020) — VEHICLE SPEED CONTROL:ACCELERATOR PEDAL Chrysler (FCA US LLC) is recalling certain 2019-2020 Ram 1500 vehicles equipped with adjustable pedals. In certain accelerator pedal positions, the floormats may prevent the pedal from returning to the normal resting (idle) position.
22V638000 (25/08/2022) — BACK OVER PREVENTION:DISPLAY FUNCTION Chrysler (FCA US, LLC) is recalling certain 2020-2021 Jeep Wrangler, RAM 1500 and 2021 Jeep Gladiator vehicles. A radio software error may prevent the rearview image from displaying. As such, these vehicles fail to comply with the requirements of Federal…
20V374000 (25/06/2020) — AIR BAGS Chrysler (FCA US LLC) is recalling certain 2020 Ram Promaster vans and 1500 pickups. The affected vehicles may have an improperly crimped diffuser in the side curtain airbag which may result in the diffuser detaching from the inflator in the…
20V580000 (24/09/2020) — SEAT BELTS Chrysler (FCA US LLC) is recalling certain 2019 Jeep Wrangler and Ram 2500, 2019-2020 Ram 1500 and 2020 Jeep Gladiator vehicles. In the event of a crash, a front seat belt retractor may not properly slow the occupant's forward movement…
18 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
NHTSA has published 1,575 manufacturer communications (service bulletins, dealer notices) covering the 2019–2026 Ram 1500.
Most cited systems: Electrical System (468), Equipment (340), Structure (189), Power Train (184), Engine And Engine Cooling (153).
Latest bulletins:
9100898 (Sep 2026) — Engine
114073 (Aug 2026) — Electrical System
114072 (Aug 2026) — Electrical System
NHTSA also opened 1 defect investigation covering these years.
Bulletin pull incomplete: 1 model year(s) failed to load (2019).
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.